• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

clutch

  1. nesralyrrej

    Engine stumble/ clutch won't disengage fully

    So it will sit and idle fine then stumble and doesn't seem to want catch its self, if you rev it up it usually goes away, but always comes back I'm thinking idle air control valve what do you guys think? Also my clutch feels stiff but doesn't disengage fully, when I got it there was no brake...
  2. Help Clutch issuies!!!!

    ok i have a 1996 ranger xlt 2.3l 4 cyl 5 speed the slave cylinder was leaking so i replaced it i cant seem to get the air out of the line i have no clutch pedal what so ever i can push it to the floor with a finger! this is how it was before i changed the slave cylinder i heard these are...
  3. 99 ranger 2wd 5 speed clutch noises

    Hello everone, I have two irritating noises in my clutch system and need help figuring out what is is so I can fix it. I am new to forums, and any bit of help is greatly appreciated 1-when starting from first and sometimes second gear (especially when cold) and riding the clutch just a little...
  4. Jerks when shift

    My truck has a manual trans an jerks hard when I shift if I don't let the clutch out REALLY slow, trans mounts? Motor mounts? Bad clutch?
  5. Clutch Push Rod?

    I'm installing a new clutch master and slave on my 1993 ford ranger xlt. I'm totally stumped on how to remove the clutch push rod from my pedal? Hoping somebody knows how? :) Thanks guys!
  6. Clutch And Throw out bearing

    So I have a problem with what I believe is my throwout bearing and potentially more. I have a 2000 Ford Ranger V6 3.0 2wd 5 speed she likes to have a subtle grind in nuetral and sometimes when i riding 60 down the road. also when i give her gas in gear she likes to slip and rev like she was an...
  7. New to clutch

    I'm hitting the age of adulthood and my dad bought me an epic 1992 Ford Ranger. It's only a 2wd though..... Problem is, I suck at driving shift. :nopityA: Anyhow, I'm learning. This truck is pretty fun to drive, even with some bits to fix up. Soon to be off roaming with it. Any good trails...
  8. 93 ranger slave or master cylinder?

    I've looked online to figure if it’s my slave cylinder or master cylinder going out. The symptoms seem to be the exact same. But I'm not replacing both. I'm taking it to the shop to get worked on, since the slave cylinder is inside the bell housing and it could get pricey. When I start the...
  9. Shifting out of first/ no clutch?

    The other day i took my 1995 Ford Ranger 5spd std. out to a mud pit went through it twice and was pulling out a 1500 silverado, yes i was successful the first time but the second time no i dropped the clutch a good few times trying to get a bit more speed and had no luck so i drove it up and...
  10. 89 2.3 clutch line wont connect

    i just got done installing new slave and master cylinders in my 98 2.3 2wd ranger and i can not for the life of me get the old clutch line to connect with the new slave. the old slave had a shiny blackish female connector, the old line has a black male connector. the new slave has black...
  11. fm145 help!!!

    Hi all, I have a delema I was hopeing to have help with. I have been workin on an 87 ranger 4wd for awhile and am getting it close to finished now. Originally it was an automatic. But I picked up a fm145. After changing the pedals and a few things around as well as tranny crossmember, I realized...
  12. Fuel Plumbing and electrical issues

    Spent about two hours searching but couldn't find it on here anywhere. I have a 92 3.0 ranger currently holding a 68 302 in it. I've got a mallory return style regulator and a 500 CFM edelbrock. I've got two problems currently. First, and most annoying, is the fuel setup. There are three lines...
  13. T5 in my 91' 5.0?

    Got a 91' 4.0l XLT that I swapped to a 5.0L H.O. and currently running a C4. Very motivated to get a T5 but I need info before I make any progress. Any info about installing clutch pedals in a 91'? Seen plenty info on setting up the bell with slave and lines etc... But I need to start from the...
  14. 84bluebronco2

    New flywheel?

    Gonna pick up a clutch kit at autozone, so should I grab a flywheel? I don't have any shuddering, but my slave is leaking... Any advice? Thanks 84BB2
  15. 4WD/Clutch issue..97 X Cab 4.0

    Hey guys,ive searched and looked and i cant find any help for the issue im having with my truck. Ill start by giving the info of the truck. 97 X Cab 4.0 5spd 4WD 6" Rough Country Lift with 33x12.50s,3.73 gears with welded front rear,new clutch 1 month ago.Also has warn hubs. Anyways,i am having...
  16. 84bluebronco2

    Clutch Kits

    So now that I have my new 1354M installed, I think I want to tear it out and do the clutch. I'm trying to do everything around the tranny but the guts themselves... I've done the shift rail plugs, changing the fluid, and putting in the shift repair kit in hopes that I'll get smoother shifts. No...
  17. owen94

    tk5 clutch pedal

    tk5 clutch pedal engages at top I have a 87 2.9l ranger with tk5 transmission. My problem is that the clutch engages maybe an inch before the top of the pedal. I have bleed the slave cylinder and it did not change a thing, wondering if this is a symptom of a worn out clutch.
  18. 3.0 Better Clutch???

    hey guys i am swaping a 1995 3.0L in to my b2300 and i want to put in a new clutch im just wondering if any one knows a good aftermarket clutch that i could use or if there are any that i can swap in from another car ive heard that a mustang clutch will work so any help wold be great
  19. weird noise when releasing the clutch

    Hey guys when I just get going in the lower ranges of first and second gear i hear this squeaking noise coming from the engine bay. It mostly happens when the engine is under strain any ideas as to the problem.
  20. 1992 ford ranger v6 3.0

    So here is the scoop. I have recently got a 1992 Ford Ranger v6 3.0 180,000 miles 2 wd. I have had a few problems with it but nothing major. I have one problem left, the truck rattles when the clutch is not pushed in, I push the clutch all the way to the floor and the noise stops. I have been...

Sponsored Ad


Sponsored Ad

Top