clutch

Hi there! I've just gotten a 1996 Ford Ranger 2.3l with 240k miles about a week ago, I got it by trading one of my flat screen TV's. :icon_rofl: When inspecting the truck for the first time, it ran good, I took the trade and drove 120 miles back to where I live. It drove great, no issues it...

Truck info: 1999, 3.0, 4x4, manual, 190k miles For a while now, my clutch pedal has been going to the floor and it's gotten increasingly more difficult to go between 1st and reverse. I was thinking that I would start with bleeding the system, removing the transmission, shooting myself, etc...

I have a 5.0 with an np435, and a f150 bell housing with that slave and the stock 84 ranger master cylinder. can't seem to get enough flow to completely disengage the clutch. the pedal is hard and feels like it normally would. anyone know if there is a different slave or different master that...

I am building a 5.0 ranger with the np435 transmission. i can not get the clutch to disengage all the way. i have the bell housing and external slave cylinder from a 1985 ford f150 and the stock 84 ranger master cylinder. I've bled the slave cylinder to the point where I have a pretty hard pedal...

ok heres the story, we have a 1993 ranger 2.3l 5 speed. yesterday, out of the blue, asa i was going through a stop light, i shifted into first, released the clutch, and nothing happened. it was just like i was in neutral. so we got it home and got it in the garage, and i came in here to do some...

I have a 97 Ford Ranger with the 2.3 and manual trans. Whenever I go to stop at any time the motor starts to stall and tries to idle at around 400 to 500 rpm's then jumps back up. It also has trouble shifting back into gear if I pull it out of gear at a dead stop, with the clutch still pressed...

I have a 1995 4.0 4X4 ford ranger with a manual transmission. A lot of times after driving for 5 minutes or so it becomes difficult sometimes to get it into gear when i come to a complete stop. The truck will go into gear if the truck is rolling but when I stop at a light I have to keep the...

Alright I have a mustang T5 in my 03 ranger edge (originally 3.0). The 98+ rangers clutch master connects into the pedal assembly itself while the 97 and earlier bolted to the firewall. I used an older ranger 7/8 bore clutch master bolted to the firewall and down to a universal 7/8 bore clutch...

Hello all, new forum member here looking for some help... I noticed when pressing the clutch down on my 2006 Ranger that the clutch pedal occasionally would make contact with part of the pedal assembly. Upon further inspection, I found that there was a little bit of lateral play in the...

Hi guys, I just found this place this week, and am planning on replacing the clutch in my newly-acquired 1992 XLT this Friday(8/14). I knew the clutch was bad when I bought the truck, however I was not aware that it was laying in pieces in the bottom of the bell housing, which I found when I...

I'm trying to find the rubber pedal cover pads to replace the worn out ones on my brake and clutch pedals, but can't seem to locate them anywhere. For a 2005 Ranger 5 speed 4 cyl. So far have tried RockAuto, Amazon, dealer site parts lookup, but all I keep coming up with is the rubber pedal pad...

According to my haynes manual 83 and 84 rangers are different when it comes to clutches. So this is for people who own/have owned or just know for certain... I think my clutch has gone out but i dont know for sure so i was hoping someone could help... Problem: ignition is off and I can put it...

Got a few questions, more just kind of curious. Couldn't find anything specific searching, didn't really know what to search for. I have a 91 2.3 2wd manual ranger with 141,xxx miles. Nothing fancy, probably the lowest base model you can go cuz I've never found anything saying my truck has a...

Hello! 1st time poster here and long time lurker, these forums have helped me quite a bit for fixing issues with my 4wd. However this time I can't see to find the same issue as what I'm having. Yesterday I finished up changing out the clutch, flywheel, and rear main seal in my Ranger, now, I...

Hi Everybody! This is my first time posting, but after combing through some of the forums it seems like a great place to get some advice. I found you all through this thread: http://www.therangerstation.com/forums/showthread.php?t=131911 Basically, my clutch pops out of 5th when I apply...

Has anyone ever rebuilt a FM146 tranny? If you have I need to know everything. Any manual or repair guide for this transmission? Do I need any special tools? How long will it take? Any expertise will help greatly.

I have a 92 Ford Ranger with a FM146 Tranny. I am hearing this rattling noise when hit the gas. I barely hear it in 1st and 2nd gear. I hear it a little more in 3rd and then the noise gets louder and worse in 4th and 5th gear. It sounds like a rattling/ bearing not properly lubed right or...

So it will sit and idle fine then stumble and doesn't seem to want catch its self, if you rev it up it usually goes away, but always comes back I'm thinking idle air control valve what do you guys think? Also my clutch feels stiff but doesn't disengage fully, when I got it there was no brake...

ok i have a 1996 ranger xlt 2.3l 4 cyl 5 speed the slave cylinder was leaking so i replaced it i cant seem to get the air out of the line i have no clutch pedal what so ever i can push it to the floor with a finger! this is how it was before i changed the slave cylinder i heard these are...

Hello everone, I have two irritating noises in my clutch system and need help figuring out what is is so I can fix it. I am new to forums, and any bit of help is greatly appreciated 1-when starting from first and sometimes second gear (especially when cold) and riding the clutch just a little...