• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

ranger


  1. Manual transmission swap problems

    So ive decided to take on the quest of a body swap from my 2008 ranger 2wd on to another 2008 but 4.0 automatic 4x4 and it ran and drove in the previous truck. Ive completed the swap but im running into problems with doing a manual transmission swap into said truck. I have changed any harnesses...
  2. 87RangerJake

    1987 Ranger 4x4 - My 1st Truck

    Decided to make a thread on my 87 Ford Ranger 2.9L 4x4 to keep track of what I've done to it and to get help fixing it up. Bought this truck back on Halloween of 2016 as my 1st car for high school and daily drove it until August 2017 when I replaced it with an 03 VW Passat for the better MPG. I...
  3. RuralRangerRoadin

    Standard Cab Long Bed VS Step Side Compatability?

    I have a 2011 2.3L 4cyl Standard Cab, and what I believe is a long bed (bed measures from cab to tailgate 6'3-4" but the tailgate has some non-factory curviture that's been implemented post manufacturing 😅 so it's hard to get a super accurate measurement) and was wondering how a 2000 Ranger Step...
  4. Looking for some help with my 94 Ford ranger

    My ranger seems to be sucking transmission fluid into the motor. I've checked the EGR I check for leaks and I can't find anything. It looked like transmission fluid was in the motor oil. Can anybody give me any insight. Greatly appreciated
  5. New member and owner of 2014 Thailand made Ford Ranger :)

    Hi guys, since I live in south east Asia, and the servicing here is really really unimpressive, (duct-tape and glue type of repairs) I'm doing most of my repairs and fixes and troubleshooting myself. But since the T6 2014 is not available in the States, its a little hard to find proper places...
  6. Stabilitrak and help

    Was wondering if my 2005 Ford Ranger 2WD has stabilitrak or not? Wanted to make sure before I lifted it. And is there any other truck mods that could turn my little white truck into a meaner newer truck?
  7. 94 Ranger Dana 35 axle shaft

    I'm looking for parts to rebuild my 4x4 axle shaft. I recently bought a 94 Ranger, 4.0L V6 - I have a few questions: anyone know where I can find parts for a Dana 35 front passenger axle shaft anyone know what years of other Fords (Explorers/Broncos) use a Dana 35 I'm in Canada; I'm 17, I'll...
  8. Brake light switch issue on my 03 Ranger XL.

    Hey guys, I have a brake light issue on my 03 Ranger XL. The brake lights come on when I move the brake light (brand new might I add, old one had same issue I'm talking about) switch up or down, but don't when I press the pedal down or do for a little bit then stops working, then when I jiggle...
  9. JodyTanner93

    Need help diagnosing a problem I’ve had for 3 months

    Hey guys I just signed up to see if anyone could point me in the right direction with my truck. I’ll start from the beginning when I bought it about 3 months ago. I’ve got a 2006 Ford Ranger xlt 2wd automatic with the 3.0 Vulcan engine. So when I first purchased the truck it ran perfect and I...
  10. Looking for STX emblem

    Hello everyone, My grandfather is restoring his 1986 Ford Ranger is looking for a STX emblem. Does anyone know where I could find one? Thank you.
  11. 2.9l injector misfire

    Good afternoon so I’m looking for help on a problem I’m having with a misfire in cylinder 3. There is spark, good fuel pressure, the cylinder has good compression and when you pull the plug after vehicle has been running the plug is completely dry. I was wondering if it could be the ecu causing...
  12. ericbphoto

    NOTICE Calendar Vote!

    After viewing almost 100 photo submissions from 18 members, I finally present to you the candidates for our 2021 TRS Calendar. I tried to choose the best from each member. Now you get to vote for the 12 that will be in the Calendar. I have also decided that there will be a second calendar of...
  13. 2.3L ('83-'97) CEL Code 222 and Partial No Spark Issue

    Hey Folks! I been lurking for a couple months. I bought a 94 Ranger 2WD manual 2.3 just recently. It has ONLY 94k miles! It didn't run great when I bought it, but I've gotten it seemingly smoothed out quite a bit with some basic maintenance. (plugs + wires, trans oil, diff oil, O2 sensor...
  14. Coogan88

    For Sale Selling my 1988 fully restored V8 Ranger 4x4

    I have decided to sell my full restored 302 and c4 transmission swapped ranger. 302 roller ford crate motor and c4 transmission with b&m shift kit and shifter. 36,xxx miles on total rebuild. Underside is show quality and the paint is in good shape with very minor scratches. Interior is in great...
  15. North Idaho 5.oh

    1994 ranger beauty/new motor!

    I know I have a few threads posted on here but what can I say, I love working on these things! I can’t remember if I ever posted this truck and if I did, I can’t seem to find the post.... What I stumbled on is a SUPER CLEAN and well taken care of 1994 ranger ex cab with a perfect rust free...
  16. FCZXTENPJVE7THTGK5A7SASJEQ.jpg

    FCZXTENPJVE7THTGK5A7SASJEQ.jpg

    Proud graduate of The Truck Driving Academy :D
  17. Melted O2 sensor connector

    2003 2WD 4.0L MFI SOHC 6cyl Ranger 122k on chassis 45k on engine Realized that my O2 sensor at S1B1 is out so I got the part at autozone and went to put it in only to find its connector in the engine compartment was melted and completely fused. Curious that a part like that would fail from...
  18. 1997 Ranger 4.0 OHV Rebuild question

    Hi, I'm new here, I have a 1994 Mazda B4000 in which I'm rebuilding a 1997 Ranger engine for. It's a 4.0 SOHC with OHV. My question is do I need to worry about where TDC is of I'm replacing both heads with brand new ones? I should just be able to turn the crank shaft until I see the pistons at...
  19. 2005 Ford Ranger transmission help!

    Hey everyone, I have a 2005 Ford Ranger 4 cyc, it has 160,000 mile on it. About 1 year ago a friend and I put a new used transmission in it. Yesterday I got in to drive it and reverse doesn’t work, popped it into drive and that doesn’t work either. Put it into 1st and it starts going so then I...
  20. Samzwell

    Taking camber out of Twin I-Beam after 2" lift (1987 Ranger RWD)

    Hey there, I need some advice on how to bring out the camber after adding 2" spacers on the front end of my '87 Ranger RWD. I did the lift after putting some Cooper Discoverer AT 235/75r15s on. I took it in for an alignment and the shop told me they can't bring the positive camber out because my...


Top