bronco 2

Hey, my 2.9 bit the dust, and I'm really considering 2.3 swapping. The only problem I'm seeing is trying to figure out what I need and then trying to source them. I think I need 2.3 4x4 engine mounts and brackets. Does anyone have a source for them? Or can I make some other mounts work? For...

I need help identifying this transmission. It was given to me and I was under the impression it was out of a 80s Bronco II (A4LD) Looking at it now, it looks more like a AODE or 4R70W. I can’t find any casting number other than on the t case adapter (pictured) Anyone familiar with these...

I'm dying to find a couple front doors for my 94' B3000 extended cab that have the vent windows. I'm almost certain the F-150 doors are a no go, but what about Bronco doors? I can't remember if they interchange with the ranger/B series, of if it's the F-series. Anyone know? Maybe where I could...

I was doing the valve stem seals on my 89 Bronco II. When I noticed on the front most pushrod on cylinder 1 fresh coolant in the lifter valley. You can see it in the photo here. I pumped some of it out and it is as if I came straight out of the coolant reservoir. Did not see any coolant...

Hey all, Did a compression test on my 1989 Bronco 2. With the 2.9l v6. Results are as following: Cyl 3: 170 psi | Cyl 6: 165 psi Cyl 2: 180 psi | Cyl 5: 165 psi Cyl 1: 180 psi | Cyl 4: 160 psi I found it weird that the compression was noticeably higher on one side. 180 also seems like its...

Hi there, I am a 21 year old college student looking to buy a project car for my dad and I to work on while I complete school. He is extremely knowledgeable about cars and engines, much more than I am, and I want to buy this bronco I found online as a suprise. However it seems possibly to cheap...

So, I'm replacing many of the parts in front end of my B2, and I end up snapping the only part I can't find anywhere The part I snapped is the Wheel Bearing adjusting nut. I can find ones for the 90 and up, but they do not fit, and there are conversion kits, but those are a bit pricy for me. Any...

I couldn’t find replacement Eddie Bauer emblems for my bronco 2 but I still had the rectangle chrome/plastic parts that surrounded them. While labeling wires in a controls cabinet at work I figured out that brother label makers have an app where you can upload and image file. One quick...

Howdy, first time posting here, I’m Jayce. I daily a 1986 Eddie Bauer bronco 2 with 85k miles and I love it but this 2.9 is perplexing me. The engine starts only if you floor it as you turn the key and quickly let off the throttle. I’ve replaced the computer as my stock one wasn’t outputting...

I have a 1987 BII and I'm thinking about doing a V8 swap here within the next year once I get some parts together. I know I'm getting a 5.0 but, I can't decide if I should go with carb or a fuel injection. I REALLY HATE car wiring and a carb engine would prevent this along with a holly sniper to...

Old pump was leaking and whining so I replaced it. Installed new pump and tried to bleed the system with the car off and the fluid level didn't go down. So I kept turning it then decided to start the car to see if that helped, still no fluid movement. Tried to drive the car and had zero power...

I am in the midst of swapping my 4.0 into my 85 bronco 2. Before pulling the engine, i had all lights and signals. After pulling the engine and engine harness there is no power to anything. Lights should be on an independent circuit, but nothing is working. Excuse my crude drawling but this is...

I need to find the exhaust manifold to exhaust system parts, so 28362 and 92690 for the 2.8l b2; I can't find anything online; if anyone has any idea where I could get these, that would be a big help.

let me pick you guys brains for a little. i recently bought a 1984 bronco 2 from a guy. he has been in the military so its been sitting for a good 8+years. well after putting a new tranny in her i finally got her running. had to fix the idle speed. when i try to start in any gear but neutral she...

Got a some pix of BIIs at the Bronco SuperCelebration in Townsend TN yesterday. Unfortunately I got there late so I might have missed a few. The purple and blue had Dana 44’s in front. Guessing they had full Early Bronco drivetrains. The camo had rear windows that came out. The red was very...

I just finished the swap To a 5 speed transmission in my 84 bronco2 and I'm hooking up the line from the master to the transmission but I can't see up there to see how the keeper pin should go in to keep the line in the top of the transmission dose any one have any pictures? Thanks again.

Hello! So I recently picked up a 1985 Ford bronco 2 2.8l v6 as more of a project vehicle I can learn from. Either way, used to run, but now it doesn't after I gave it a tuneup lol so I'm trying to track down what got it not starting, So, I've checked for spark on sparkplugs got em, got...

Hello, I'm looking for transmission crossmember brackets for a 1988 ford Bronco 2. Mine is rusted out. It is the part that connects the crossmember to the frame. I have searched all over the internet and don't know where to find them. Anything helps! Thank you!

Hello, I'm starting to do an axle swap on my 88 Bronco II with a dana 30 out of a jeep cherokee. I'm posting to get some advice on the best way to tackle this and maybe a list of what parts I'm going to need to be able to make it a mostly bolt on job.

I'm in the middle of restoring my B-Deuce. It's a 1990 Bronco 2 Eddie Bauer Edition, with the Dana 35 Front end. I lucked out on the last one. I'm wondering if anyone can recommend a product for conditioning/restoring my dried out, and cracking rubber window seals, for the large, side-rear...