• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

2.8 rear main oil seal replacement?


84_Nor*Cal_Ranger

New Member
Joined
Jan 12, 2010
Messages
81
Reaction score
0
Points
0
Location
Lake County, CA
Vehicle Year
1984
Make / Model
Ford
Engine Size
2.8
Transmission
Automatic
how hard is it to replace the rear main oil seal? i have a oil leak coming from my bell housing.
 


kimcrwbr1

Well-Known Member
Joined
Dec 6, 2009
Messages
6,044
Reaction score
46
Points
48
Location
maplevalley WA
Vehicle Year
1983
Make / Model
ford
Engine Size
2.8l
Transmission
Automatic
That is another animal you might be able to raise the engine enough to pull the pan and rear main cap and put a two piece seal in or drop the front end but however you do it put a new high volume oil pump in it. are you sure it is the rear main did you have a new O ring on the dizzy when you put it in. was it real tight to install it
 

84_Nor*Cal_Ranger

New Member
Joined
Jan 12, 2010
Messages
81
Reaction score
0
Points
0
Location
Lake County, CA
Vehicle Year
1984
Make / Model
Ford
Engine Size
2.8
Transmission
Automatic
yep new o ring and it was very tight when it was installed.
 

Big Jim M

New Member
Joined
Apr 18, 2008
Messages
2,728
Reaction score
30
Points
0
Age
86
Location
Austin
Vehicle Year
2002
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
Howdy 84. You are aware of a failing pcv causing excessive pressure in the crankcase and PUSHING oil out the rear seal...aren't you? I always replace the pcv before thinking of working on that seal. In the event of a little too much blowby I have hooked the valve cover directly to vacuum without a pcv and had good luck with the oil leak.
Big JIm
 

84_Nor*Cal_Ranger

New Member
Joined
Jan 12, 2010
Messages
81
Reaction score
0
Points
0
Location
Lake County, CA
Vehicle Year
1984
Make / Model
Ford
Engine Size
2.8
Transmission
Automatic
thanks im just trying to figure out where to hook my pcv valve up at. my motocraft 2100 didnt have a spot at the base like the old feed back one. any tips on where to hook it up?
 

Big Jim M

New Member
Joined
Apr 18, 2008
Messages
2,728
Reaction score
30
Points
0
Age
86
Location
Austin
Vehicle Year
2002
Make / Model
Ford
Engine Size
4.0
Transmission
Manual
Yep! Anywhere you can cut a vac hose and put a "T" in will be ok! In particular one on the carb is best but anywhere will work.
Big JIm
 

84_Nor*Cal_Ranger

New Member
Joined
Jan 12, 2010
Messages
81
Reaction score
0
Points
0
Location
Lake County, CA
Vehicle Year
1984
Make / Model
Ford
Engine Size
2.8
Transmission
Automatic
the rear main is still leaking after i replaced the pcv. so i m running some bars leak to see if that helps. if not i have a friend to help me replace it.
 

Eric Kropp

New Member
Joined
Oct 16, 2007
Messages
195
Reaction score
2
Points
0
Location
Prunedale CA
Vehicle Year
1983
Make / Model
Ford
Engine Size
2.8
Transmission
Manual
The rear main seal on my 1983 2.8 is a one piece unit and you must remove the tranny, clutch and flywheel to get to it. I would presume all Ranger 2.8's are the same. Notice, I did say "presume". But mine is difinitely one piece.

Eric
 

kimcrwbr1

Well-Known Member
Joined
Dec 6, 2009
Messages
6,044
Reaction score
46
Points
48
Location
maplevalley WA
Vehicle Year
1983
Make / Model
ford
Engine Size
2.8l
Transmission
Automatic
I wasn`t sure wether there was a two piece seal. I had a dodge 360 and put a two piece seal in but the parts guy gave me a ford 360 seal it seemed to fit ok not knowing and when I started it it made a spinning noise and proceeded to drain the pan on the garage floor of my brothers new house his wife was pissed.
 

kimcrwbr1

Well-Known Member
Joined
Dec 6, 2009
Messages
6,044
Reaction score
46
Points
48
Location
maplevalley WA
Vehicle Year
1983
Make / Model
ford
Engine Size
2.8l
Transmission
Automatic
Those high volume pumps work pretty good tho. He He
 

dangerranger83

5.0 HO under the hood!!!
Supporting Member
V8 Engine Swap
Solid Axle Swap
Joined
Apr 26, 2009
Messages
7,738
Reaction score
54
Points
0
Location
Lafayette, IN
Vehicle Year
1983
Make / Model
Ford
Engine Size
5.0 HO carbed with an np435 and np208
Transmission
Manual

Sponsored Ad


Sponsored Ad

Members online

No members online now.

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Mudtruggy
May Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top