ranger

1989 ford ranger, 2.9v6 manual STX I could really use some help locating where this Galley plug is supposed to go there is 3 in total, two are already installed on the back of the block just next to the freeze plug. (if you look to the front of the block, left, you see a galley plug is...

So I drive a 2000 Ranger 4.0L V6 4x4 with just over 180k on it. Y'all know how many great things there are about the 4.0, but gas mileage is definitely not one of them! I'm averaging I'd say around 14.7-15 MPG, and the highest I've gotten is around 16.5. This is a bit problematic, since I drive...

So ive decided to take on the quest of a body swap from my 2008 ranger 2wd on to another 2008 but 4.0 automatic 4x4 and it ran and drove in the previous truck. Ive completed the swap but im running into problems with doing a manual transmission swap into said truck. I have changed any harnesses...

Decided to make a thread on my 87 Ford Ranger 2.9L 4x4 to keep track of what I've done to it and to get help fixing it up. Bought this truck back on Halloween of 2016 as my 1st car for high school and daily drove it until August 2017 when I replaced it with an 03 VW Passat for the better MPG. I...

I have a 2011 2.3L 4cyl Standard Cab, and what I believe is a long bed (bed measures from cab to tailgate 6'3-4" but the tailgate has some non-factory curviture that's been implemented post manufacturing 😅 so it's hard to get a super accurate measurement) and was wondering how a 2000 Ranger Step...

My ranger seems to be sucking transmission fluid into the motor. I've checked the EGR I check for leaks and I can't find anything. It looked like transmission fluid was in the motor oil. Can anybody give me any insight. Greatly appreciated

Hi guys, since I live in south east Asia, and the servicing here is really really unimpressive, (duct-tape and glue type of repairs) I'm doing most of my repairs and fixes and troubleshooting myself. But since the T6 2014 is not available in the States, its a little hard to find proper places...

Was wondering if my 2005 Ford Ranger 2WD has stabilitrak or not? Wanted to make sure before I lifted it. And is there any other truck mods that could turn my little white truck into a meaner newer truck?

I'm looking for parts to rebuild my 4x4 axle shaft. I recently bought a 94 Ranger, 4.0L V6 - I have a few questions: anyone know where I can find parts for a Dana 35 front passenger axle shaft anyone know what years of other Fords (Explorers/Broncos) use a Dana 35 I'm in Canada; I'm 17, I'll...

Hey guys, I have a brake light issue on my 03 Ranger XL. The brake lights come on when I move the brake light (brand new might I add, old one had same issue I'm talking about) switch up or down, but don't when I press the pedal down or do for a little bit then stops working, then when I jiggle...

Hey guys I just signed up to see if anyone could point me in the right direction with my truck. I’ll start from the beginning when I bought it about 3 months ago. I’ve got a 2006 Ford Ranger xlt 2wd automatic with the 3.0 Vulcan engine. So when I first purchased the truck it ran perfect and I...

Hello everyone, My grandfather is restoring his 1986 Ford Ranger is looking for a STX emblem. Does anyone know where I could find one? Thank you.

Good afternoon so I’m looking for help on a problem I’m having with a misfire in cylinder 3. There is spark, good fuel pressure, the cylinder has good compression and when you pull the plug after vehicle has been running the plug is completely dry. I was wondering if it could be the ecu causing...

After viewing almost 100 photo submissions from 18 members, I finally present to you the candidates for our 2021 TRS Calendar. I tried to choose the best from each member. Now you get to vote for the 12 that will be in the Calendar. I have also decided that there will be a second calendar of...

Hey Folks! I been lurking for a couple months. I bought a 94 Ranger 2WD manual 2.3 just recently. It has ONLY 94k miles! It didn't run great when I bought it, but I've gotten it seemingly smoothed out quite a bit with some basic maintenance. (plugs + wires, trans oil, diff oil, O2 sensor...

I have decided to sell my full restored 302 and c4 transmission swapped ranger. 302 roller ford crate motor and c4 transmission with b&m shift kit and shifter. 36,xxx miles on total rebuild. Underside is show quality and the paint is in good shape with very minor scratches. Interior is in great...

I know I have a few threads posted on here but what can I say, I love working on these things! I can’t remember if I ever posted this truck and if I did, I can’t seem to find the post.... What I stumbled on is a SUPER CLEAN and well taken care of 1994 ranger ex cab with a perfect rust free...

Proud graduate of The Truck Driving Academy :D

2003 2WD 4.0L MFI SOHC 6cyl Ranger 122k on chassis 45k on engine Realized that my O2 sensor at S1B1 is out so I got the part at autozone and went to put it in only to find its connector in the engine compartment was melted and completely fused. Curious that a part like that would fail from...

Hi, I'm new here, I have a 1994 Mazda B4000 in which I'm rebuilding a 1997 Ranger engine for. It's a 4.0 SOHC with OHV. My question is do I need to worry about where TDC is of I'm replacing both heads with brand new ones? I should just be able to turn the crank shaft until I see the pistons at...