ANOTHER water pump dead. This is the 3rd water pump i'm replacing in a month. They are always failing at the shaft seal/bearing.
What can I possibly be doing wrong to kill the water pump again?
C:>
All of a sudden, my turn signals won't work. Other than the flasher/fuse... am I overlooking something silly that would prevent ALL turn signals from lighting up?
Thanks a bunch!
C:>
I just want to make sure I understand this correctly.
If I'm not mistaken, as I stand in front of the engine the cylinders are as follows:
3 - 6
2 - 5
1 - 4
But the coil pack is arranged:
3 - 5
2 - 6
1 - 4
Could someone please confirm... or correct me?
93 Ranger, V6 4.0
I ran a cylinder balance test, trying to identifya miss, and got a code 20 (cylinder #2 not firing properly) code.
I have installed new spark plugs, new wires and checked compression. Compression reads 180 on that cylinder (compression in other cylinders ranged from 165 to 180).
Any suggestions?
Performing a Key On, Engine Off test, I received codes 173 and 176.
According to my code reader reference, that means I have an HEGO sensor fault (rich) and HEGO sensor fault, always lean.
Could someone please shed some light in "plain english" on how to fix this problem?
Thanks a bunch!
C:>
I'm looking at replacing my coil pack (93 Ranger, 4.0L, V6), and more for affordability rather than performance, I've run into the ACCEL coil packs on e-bay.
Is anyone running these? are they worth it? or am I going to regret going with the aftermarket components?
Thanks a bunch!
I am not sure if we have a good wiring diagram/schematic of the engine bay for a 93 4.0. But the connector I am trying to hook up has a blue and a white wire (about gauge 14), with a black plastic cap/holder. It is (in my car) coming out of the wiring loom, just under the throttle cable and it...
I have a 93, 4.0. Just replaced the head gasket and getting ready to fire it up for the first time (truck is new to me). Could you please let me know where the ECU is so I can see if I'm getting any error codes?
Thanks a bunch!
C:>
Looking for pix of a clean engine bay for a 4.0... circa 93. I'm doing a head gasket job... and I want to make sure I connect everything just right... but clean pictures are so pretty....
C:>
I am working on a 93 4.0 ranger with a blown head gasket. I noticed the gasket kit comes with exchaust manifold gaskets... but the truck didn't have gaskets when torn.
Any suggestions? should I use the manifold gaskets anyway?
I'm wondering... I have a 93 Ranger 4.0. Need to replace heads. Will later i.e. 97/98 heads bolt on? what differences in performance would I notice? will all other items bolt on?
Thanks,
Carlos
I have a 93 2WD that I just acquired, and I would like to use it for towing. It has all the wiring in place, which is a plus. However, the whole truck is just a little too high for my taste. I really would like to lower it (and my trailer hitch is only about 17" of the ground so I would...
What would be involved in doing this? I hear the heads are a little different, but would the intake manifolds, ecu, etc. work? Or could I do it with the 93 setup?
Thanks,
Carlos
Hi,
I'm not sure if this is the best place to post this question, but I invite the ADMIN team to move as needed.
I have a 93 Ranger, regular cab, with a 3.0 engine. The truck is a new acquisition... and I've noticed it rides a little high. I really want to drop the truck about 3-4 inches.
I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.