• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

1984 b2 2.8 trans


timmytim

New Member
Joined
Mar 25, 2016
Messages
4
Reaction score
0
Points
1
Vehicle Year
1984
Make / Model
Ford
Transmission
Manual
My current work truck is my 84 b2 that has the tk4. It has either a shot shifter fork or bad 1st gear synchronizer..

Ive got two tk5sp trans- first one we pulled apart to rebuild has a bad main shaft. Its been down so long Im going to just throw the second one in and if it pulls in all gears Im just gona drive as is.

Ive had hard time finding parts for those tk5's and wonder if there is another 5spd that will bolt to my 2.8 without modification? Thanks
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,363
Reaction score
8,370
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
Welcome to TRS :)

Yes, the M5OD-R1 5-speed from a 4.0l will bolt to the 2.8l block/engine

M5OD-R1 doesn't have a detachable bellhousing, so must be from 4.0l engine and a 4x4 if so equipped.
2.9l M5OD-R1 will also work but they were 2WD only

You will want a 1997 or older M5OD-R1, if 2WD, it will have the speedometer gear you need, 1998 and up didn't have that.
If 4x4 then you can use your current transfer case with any year 4.0l 4WD M5OD-R1, 1990-2012, even the HD model, since transfer case has speedometer hook up
BW1350 and 1354 have same bolt pattern

But there is modifications needed:
Transmission support needs to be moved, and driveshaft lengths change
 
Last edited:

timmytim

New Member
Joined
Mar 25, 2016
Messages
4
Reaction score
0
Points
1
Vehicle Year
1984
Make / Model
Ford
Transmission
Manual
Welcome to TRS :)

Yes, the M5OD-R1 5-speed from a 4.0l will bolt to the 2.8l block/engine

M5OD-R1 doesn't have a detachable bellhousing, so must be from 4.0l engine and a 4x4 if so equipped.
2.9l M5OD-R1 will also work but they were 2WD only

You will want a 1997 or older M5OD-R1, if 2WD, it will have the speedometer gear you need, 1998 and up didn't have that.
If 4x4 then you can use your current transfer case with any year 4.0l 4WD M5OD-R1, 1990-2012, even the HD model, since transfer case has speedometer hook up
BW1350 and 1354 have same bolt pattern

But there is modifications needed:
Transmission support needs to be moved, and driveshaft lengths change
Thank you. This is what I needed to know!!
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,342
Reaction score
17,835
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
But there is modifications needed:
Transmission support needs to be moved, and driveshaft lengths change
M5OD is the same length as an A4LD so factory driveshafts are out there that will work. Some of the other transmissions maybe the same, the TK series are confusing to an outsider and I have never had to deal with them so I can't keep them straight.

M5OD may use the same crossmember as an A4LD too. When I V8 swapped my '85 I slid the factory crossmember ahead and there were holes already there for it but the frame rails were closer together there, I had to trim about 1/2" off of the crossmember.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top