• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Lumbar Buckets in a Gen1


3hokies

New Member
Joined
Jun 27, 2011
Messages
109
Reaction score
0
Points
0
Location
Winchester, VA
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9L
Transmission
Automatic
So I scored a set of buckets with Lumbar supports for my '88 Reg. Cab...any suggestions for wiring them?
 


3hokies

New Member
Joined
Jun 27, 2011
Messages
109
Reaction score
0
Points
0
Location
Winchester, VA
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9L
Transmission
Automatic
Anybody????
 

85_Ranger4x4

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Article Contributor
V8 Engine Swap
OTOTM Winner
TRS Banner 2010-2011
TRS 20th Anniversary
VAGABOND
TRS Event Participant
Joined
Aug 7, 2007
Messages
32,342
Reaction score
17,837
Points
113
Location
SW Iowa
Vehicle Year
1985
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Manual
One wire is hot (with a fuse) and one wire is ground.
 

3hokies

New Member
Joined
Jun 27, 2011
Messages
109
Reaction score
0
Points
0
Location
Winchester, VA
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9L
Transmission
Automatic

Mark_88

Well-Known Member
Joined
Aug 11, 2007
Messages
18,554
Reaction score
240
Points
63
Age
68
Location
Ontario, Canada
Vehicle Year
2007
Make / Model
Dordge
Engine Size
3.3 Fuel Injected
Transmission
Automatic
My credo
Love Thy Neighbor
I've got a set of them but never plugged them in...there is actually a 30 amp breaker in the fuse panel for power seats...you might want to run it through that...
 

3hokies

New Member
Joined
Jun 27, 2011
Messages
109
Reaction score
0
Points
0
Location
Winchester, VA
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9L
Transmission
Automatic
good to know
 

3hokies

New Member
Joined
Jun 27, 2011
Messages
109
Reaction score
0
Points
0
Location
Winchester, VA
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9L
Transmission
Automatic
ok, so I've got 18" of wiring harness and I'm gonna ground them to the cab....any suggestions for the hot wire?
 

fyre82

Member
Firefighter
TRS Banner 2012-2015
Joined
Dec 1, 2007
Messages
689
Reaction score
6
Points
18
Location
Lake Almanor, Ca.
Vehicle Year
1988/2000
Make / Model
Ford
Engine Size
2.9/4.0
2WD / 4WD
4WD
Total Lift
9" on the 2000, 6" on the '88
Tire Size
265/75/16, 31x10.50x15
My credo
The memories of a man in his old age are the deeds of a man in his prime
Just wire it to a ignition on or direct hot somewhere.
 

3hokies

New Member
Joined
Jun 27, 2011
Messages
109
Reaction score
0
Points
0
Location
Winchester, VA
Vehicle Year
1988
Make / Model
Ford
Engine Size
2.9L
Transmission
Automatic
thanks man, hopefully doin it Monday
 

Mark_88

Well-Known Member
Joined
Aug 11, 2007
Messages
18,554
Reaction score
240
Points
63
Age
68
Location
Ontario, Canada
Vehicle Year
2007
Make / Model
Dordge
Engine Size
3.3 Fuel Injected
Transmission
Automatic
My credo
Love Thy Neighbor
Well, the hot wire should run through the fuse panel...but you can run it directly...I'd put it on the breaker though just to be sure...not much to do other than run the wire under the carpet and up to the fuse panel...
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top