Steering won't come back....

Sworn · Dec 12, 2007

Could really use some steering advice.....My 88 4X4 Ranger has some steering issues. Keep in mind it's almost 20 Years old and has a seven inch lift kit.

The truck was run with 35's and now has regular small truck tires. (I have a set of 33's on order.)

Anyway, when you turn the wheel to make a left or a right the steering won't return. You have to manually turn it back......It's not hard and still has the power assist. The power steering isn't leaking any fluid. What do you guys think? Power steering box? Tie Rods?

Thanks in advance

Jspafford · Dec 12, 2007

If I had one guess I am going to go with steering box.

rickcdewitt · Dec 12, 2007

the small tires would put it out of alignment if it was aligned with 35's,that might have something to do with it.

du510 · Dec 12, 2007

rickcdewitt said:
the small tires would put it out of alignment if it was aligned with 35's,that might have something to do with it.

how is that?

Sworn · Dec 12, 2007

If I had one guess I am going to go with steering box.

That's kinda what I'm thinking.....

kunar · Dec 12, 2007

i dont think smaller tires would throw it out of alignment but if your caster was off, that could be the problem

rickcdewitt · Dec 13, 2007

have any of you geniuses aligned a ttb(yourself?),and or experimented with different rim and tire combo's?? when you move the centerline of the tire in or out it changes the leverage and therefore camber and caster.i'de bet money his camber and maybe caster are out of spec.those would be some very skinny 35's to sit where a 235/75 sits.the question he needs to ask is-did it work normally(as much as it can with 35's) right before changing wheels?its likely 35's could have worn out the steering box but thats not his only problem,besides he says it has power assist on the return he just has to return it himself(alignment,frozen balljoint or u-joint).

MAKG · Dec 13, 2007

I've done camber and toe alignments the old fashioned way (bubble level and a string). It's a big PITA and not THAT accurate. Definitely close enough to get to the alignment shop....

Things that can cause poor return:

1. Excessive toe-out (will also wander)
2. Overtightened steering box -- this is not something that happens by itself
3. Binding balljoint(s) -- are they greaseable? Have they been greased recently?
4. Binding steering linkage

These are things you can figure out with a major inspection. To find the binding, you have to disconnect stuff, unless you're lucky and you can see it.

rickcdewitt · Dec 13, 2007

MAKG said:
I've done camber and toe alignments the old fashioned way (bubble level and a string). It's a big PITA and not THAT accurate. Definitely close enough to get to the alignment shop....

i was talking about on an alignment rack,not in a garage(the bodyshop has one),and yes-
1)visually check for broke parts- then fix if needed
2)throw it on a rack and see what you have.
3)use the frame puller or throw new parts on as needed
4)re-align
pretty simple process really

Steering won't come back....

Sworn

New Member

Jspafford

Logan Andrew Feb 17, 2012

rickcdewitt

New Member

du510

New Member

Sworn

New Member

kunar

Forum Staff Member

rickcdewitt

New Member

MAKG

New Member

rickcdewitt

New Member

Sponsored Ad

Sponsored Ad

Staff online

Members online

Member & Vendor Upgrades

Latest posts

Truck of The Month

Recently Featured

Follow TRS On Instagram

Latest Album Photos

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store

Sponsored Ad

Sponsored Ad

Sponsored Ad

Amazon Deals