Mikeg1988xlt
Member
My left turn signal on the truck is very dimly flashing if the lights are turned on. If the lights are off it flashes like it should. I followed the install instructions.
-
Welcome Visitor! Please take a few seconds and Register
for our forum. Even if you don't want to post, you can still 'Like' and react to posts.
Turn signal after trailer plug install
- Thread starter Mikeg1988xlt
- Start date
- Joined
- Jan 23, 2011
- Messages
- 767
- City
- Bronson Michigan
- Vehicle Year
- 1985
- Engine
- 2.8 V6
- Transmission
- Manual
- Total Lift
- 6” skyjacker 2” body
- Tire Size
- 33x12.5
With or without the trailer hooked to it?
Mikeg1988xlt
Member
Both hooked up and unhooked
- Joined
- Jan 23, 2011
- Messages
- 767
- City
- Bronson Michigan
- Vehicle Year
- 1985
- Engine
- 2.8 V6
- Transmission
- Manual
- Total Lift
- 6” skyjacker 2” body
- Tire Size
- 33x12.5
Sounds like you have the lights on the left turn signal. I would redress the instructions and review your install.
Mikeg1988xlt
Member
Thank you.
vigness
Well-Known Member
- Joined
- Dec 11, 2016
- Messages
- 120
- City
- Princeton, KS
- Vehicle Year
- 2003
- Engine
- 4.0 V6
- Transmission
- Automatic
Sounds like a bad / broken ground wire.
Mikeg1988xlt
Member
I think you're right. After undoing the plug wiring it still dose it.
vigness
Well-Known Member
- Joined
- Dec 11, 2016
- Messages
- 120
- City
- Princeton, KS
- Vehicle Year
- 2003
- Engine
- 4.0 V6
- Transmission
- Automatic
The weak light is indicative of that circuit back feeding to another for a ground. With no power on the back feed, it gets a good ground, power on and it's a bad ground.
RobbieD
2.9l Mafia
- Joined
- Aug 6, 2007
- Messages
- 4,948
- City
- Georgia
- Vehicle Year
- 1984,1990,1994
- Transmission
- Manual
- My credo
- Toonces drives a Ranger . . . . just not very well.
Likely a bad ground.
Did the trailer harness use "scotchlok" connectors that you use squeeze with pliers to make a metal blade "bite" into the wire? These are notorious for damaging the copper wire strands inside the insulation.
Did the trailer harness use "scotchlok" connectors that you use squeeze with pliers to make a metal blade "bite" into the wire? These are notorious for damaging the copper wire strands inside the insulation.
Mikeg1988xlt
Member
Did anyone know you could install the bulb backwards? Because I sure didn't lol. Rewired the new TL socket which was installed a few months ago and was still at a loss. Did some more research and found someone saying the bulb could be in backwards. Thought it was crazy but gave it a shot. Turns out it was crazy enough to work lol. Thanks for the quick feedback.
Snoranger
Professional money waster
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
RBV's on Boost
ASE Certified Tech
VAGABOND
TRS Event Participant
GMRS Radio License
TRS 25th Anniversary
- Joined
- Nov 25, 2007
- Messages
- 13,850
- State - Country
- NJ - USA
- Vehicle Year
- '79,'94,'02,'23
- Vehicle
- Ford Ranger
- Engine
- 2.3 EcoBoost
- Transmission
- Automatic
- My credo
- I didn't ask for your life story, just answer the question!
An 1157 can be installed backward with enough force. The only thing that will happen is the marker light will be bright and the stop/turn will be dim... opposite of normal.
If a 1156 is installed (or a 1157 is installed a little crooked, at the right angle, in a cheap tail light housing) it will short both the marker and turn together. When you turn that blinker on, the marker lights will flash. The same thing can happen if a 1157 shorts internally.
Similar threads
Sponsored Ad
Sponsored Ad
TRS Events
Member & Vendor Upgrades
For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.
Latest posts
-
-
-
-
-
-
-
-
'97 F350 PSD clutch recommendation, now build and whatnot saga :)- Latest: scotts90ranger
Recently Featured
Ranger Adventure Video
TRS Merchandise
Follow TRS On Instagram
