dangerranger1983 build

[dangerranger83]

I asked the fiancee about turing it into a table and her response was "I'm somewhat less them amused". I just don't have the heart to take the engine apart. But if i was going to make an engine table, it would be a 302.

I'm handling the stress fine. I only smoke two cigs a day, one to and one from work, on the week days but weekends it many be more or less. I'm not really smoking cigs, more like cig cigars. If i do drink, its about a shot glass of Jack in a huge cup of Cola.

Sent from my SPH-D710 using Tapatalk 2

 

[Psychopete]

enjoy the calm before the storm lol

 

[dangerranger83]

There isn't going to be any calm anytime soon. I was told that my work is going to have shut down Thanksgiving week then turn back around and have shut down from December 17th to January 7th. So my fiancée is going to have to find a job now so that we can make it through. I might have to find a part time job during that time too.

But i told her hell or high water, we will get married on February 22nd like we had planned.

Sent from my SPH-D710 using Tapatalk 2

 

[dangerranger83]

The fiancée has a job interview at best buy Sunday so hopefully she gets that job, even if its temp, just enough to help get through the winter months. I am also selling my ak-74 at the end of the month to a guy. I have no real attachment to the gun so I'm not going to lose sleep selling it. Future plans are to buy an AR-15, much easier to find ammo for it.

Sent from my SPH-D710 using Tapatalk 2

 

[dangerranger83]

I have Thanksgiving week off work. The good new is my bday is on the 19th and that's also the first week of gun season for deer hunting. Bad news it's a week off that i don't want off and hopefully be able to afford to go hunting.

Truck runs great by have no time to get looking at getting her 4wd again let alone the money, well not until after this next paycheck and if the fiancée gets the or a job.

Sent from my SPH-D710 using Tapatalk 2

 

[dangerranger83]

Since photobucket has changed and I can load the old look on my computer, had to use the photo to upload the photo here.

Anyways heres the situation. The original crossmember I used due to I had to get the truck done in a pintch. Was slightly modded on the passenger side to bolt up and the driverside was bolted under the mount instead of over. Also as seen, it and the mount are in the path of a front driveshaft. Anyways the I could mod this current trans crossmember to work until I get money to make a new one and as cheap as possible? Edit the picture if needed, suggestions, etc...

Sent from my SPH-D710 using Tapatalk 2

 

[Robert_1967]

That isn't going to work, time to get out the torch and cut some stuff, or is there a way you can clock the transfer case down a bit ?



Robert

oh read this ad on Craigslist, I laugh my rear end off reading this and thinking of your truck
http://knoxville.craigslist.org/cto/3414917666.html

posted with a picture of Gonzo and a glass of tea.

 

[dangerranger83]

No way of clocking it. I could add to the crossmember to make the down part move over and movet the mount to the outside of the frame.

 

[dangerranger83]

Well I'm 24 years old now. Have the week off work too.

Sent from my SPH-D710 using Tapatalk 2

 

[escort_gts]

Happy Birthday

Sent from my HTC VLE_U using Tapatalk 2

 

[Robert_1967]

Well, Happy Birthday.



Robert





posted with a meowing cat.

 

[dangerranger83]

Thanks guys.

Sent from my SPH-D710 using Tapatalk 2

 

[Rowdy Fitzgerald]

Happy birthday! Hey where are you from? I'm planning a trip to Florida in a couple months. It would be cool to see your rig!

 

[Twister]

Happy birthday! I just turned 22 in September, its scary how fast times goes by

 

[dangerranger83]

I'm in Indiana. I do agree the time guess by fast. Before i know it i will be holding my first child.

Sent from my SPH-D710 using Tapatalk 2