• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

3/4 ton brakes on F150 D44


^^^those guys, not trail gear.... my bad!
 
Trail worthy fab does recentered H1's with double bead locks. Really good wheels, I recommend them if you want to run mil tires or you'll have to get good at remounting a tire on the trail. Mil tires don't have a safety bead and will come off the rim if under inflated.

Sent from road while ignoring traffic

The rim has the safety bead not the tires. Those don't normally have anything because they are 16.5" tires. I just run mine tubed doesn't really matter if I loose a bead.
 
Tube as in inner tube? Will that keep the bead on the wheel at low psi? I meant that the bead on the tire is round not flat like a normal tire. It will come off on a non bead locked wheel at low psi.

Sent from road while ignoring traffic
 
Tube as in inner tube? Will that keep the bead on the wheel at low psi? I meant that the bead on the tire is round not flat like a normal tire. It will come off on a non bead locked wheel at low psi.

Sent from road while ignoring traffic

The bead is flat. I have a set. They are not any different than any other tire.

As for the tube it works the same as a bike tube...
 
I know plenty of people running mil tires on standard 16.5 rims and have had no issue at around 20 psi with no beadlocks or screws.

Sent from my C771 using Tapatalk 2
 
If you can find a mid-late 70's 3/4 ton D44, you can swap the brake caliper bracket directly onto an F150 knuckle. Actually you can swap any of it, the bolt pattern for the 3/4 ton spindle is exactly the same.

The issue you will run into is that since the 3/4 ton rotor is much larger, you won't be able to use your 1/2 ton rotor. This is solved by using your 1/2 ton spindle and a late model Dodge front brake rotor. A buddy of mine did this exact setup on a Jeep. There was some minor machine work that had to be done to the rotor I believe, but otherwise it is a bitchin setup and you gain dual piston calipers with the 3/4 ton stuff.

One other thing of note is that you CANNOT put 1/2 ton brakes on a 3/4 ton knuckle without doing major reconstructive surgery to the knuckle. The caliper won't even come close to fitting. Just FYI, I had a set of flat top knuckles from a 3/4 ton D44 that I considered using but it's way too much work for a modified knuckle that is potentially dangerous.

I know plenty of people running mil tires on standard 16.5 rims and have had no issue at around 20 psi with no beadlocks or screws.

Sent from my C771 using Tapatalk 2

I know a few people too, the problem is that military tires are very stiff and the rubber compound is very hard. Really bad choice for offroad tires. Better to go with a different tire if you REALLY want 16.5's, OR just do it once and do it RIGHT and get 17" wheels.
 
Picked up t bird calipers and F350 master. I think I am going to stick with 35s for a while. I like the gearing as it sits. Nice for dd and weekend wheeling. 4.56s may still be in the near future though.

Sent from my C771 using Tapatalk 2
 

Sponsored Ad


Sponsored Ad

TRS Events

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Ranger Adventure Video

TRS Merchandise

Follow TRS On Instagram

TRS Sponsors


Sponsored Ad


Sponsored Ad


Amazon Deals

Sponsored Ad

Back
Top