Search results

We've got and 84 Std Ranger with a 302, C-4, and a 7.5" rear end..the driveshaft has to be shortened we know that...We need to know what model, make and year slip yoke will fit our factory Ranger driveshaft (original trans was a C-3 if that helps) what driveshaft have you guys used that will...

Does anyone know what these wheels came on...my dad had 2 in storage and i thought i would try this forum first. They're are 15" x 8/12" aluminum 6 lug inside they say "SHELBY CAL 500"

We have recently just bought a TCI Sizzler torque converter and we have a bit of a problem. When the trans is not hooked up to the motor the motor turns over by hand easily, but when it's hooked up to the engine it won't turn over, even with a breaker bar. We took the trans off to try a...

i'm building a 302 and so far it's in the short block form...but i can't turn it over by hand even with the balancer as leverage...my main bearing clearence was a little under 0.002"...is the to tight and the source of the problem

Why did ford use a 28oz imbalance on the flywheel, balancer, etc...It is cuz of the firing order causing stress on the front main cap

Sorry about not continuing on with the last post, i had a change of plans, but here are the new ones. Project should take 1 1/2 years at the most! 0.030" over, hyper pistons, ported heads and gasket matched intake, balanced, XE256H Comp Cam or Lunati Street Avenger (to be decided) 600cfm carb...

when disassembling my 302 for maching, i noticed something very intersting about the oil supply holes for the main bearings. I talking about the one drilled into the block....ummm. There 2 of them per journal and it does NOT look factory. The bearing themeselves had one hole. Is something wrong...

i doing a performance rebuild on my 302 and i was thinking of getting Manley Stainless valves...now in a book i've got that all about Domestic engines it says my valves measure 1.773-1.783 on the intake. Can i use a valve that measures 1.785? it's the smallest Manley offers. The exhaust is...

I know this is gonna be a stupid question for most people to answer...but i can't figure out how to remove the camshaft for a '72 302. Nothing online is giving me answers...anyone help...FYI This is my first time removing a camshaft.

Ok, so I just got a flowmaster Super 44 on my 91 4.0L. It was connected back to the pipe after the cat. The pipe is 2 1/4" mandrel bent. Without a turndown after the muffler, the truck SOUNDS AMAZING both inside and out, but when i put the turndown on, it completely kills the sound! What's going...

feellnfroggy! you made some good points. One thing though is the running 60+ in 4wd...i wouldn't be doing that...only in RWD. I'd only use 4wd when there's snow or i'm towing someone in the dirt or whatever.

taking out the blocks was how i planned to do the rear. I had thought about custom front with QA1 coilovers(2 eyelet mounts). Put a thick and braced plate over the hole in the spring pocket. Custom mounts put it would cost a lot...Once again Capt Jay. Since you apparently can't read...Why Lower...

don't need to get sarcastic there jay. sorry if i don't follow the trends like you seem to do...i want something different...what's wrong with that?

the street look is what i'm really going for...Lifting was my first choice obviously but everyone is lifting and i want to be different...Just answer my first question...Will the belltech springs work and could it be realigned.

i'm having a delema with myself. I would like to play in some mud, but i would also like to be able do 85+ on the freeway. So why not do 85 on the way to some old dirt roads then do some rally racing in the mountains. Plus i've put to much money into this truck to go and buy a 2wd.

Now don't get all anal or whatever saying it's a stupid idea and i should lift it...just shut up...But well the belltech 2 in coils fit a 4wd...If so can i get the truck to realign camber wise. I had an idea of a Rally truck for like dirt roads and such...something different. and no i won't just...

I know this is a little off as far as questions but...Can someone tell me the dimensions of either the front or rear coils. From the pictures i've seen (of the rear coils...i think) they look like the would fit on the front of my ranger...They have a wide top and narrow bottom. My ranger is '91...

I do know i get 4wd but when i try the low range button the light doesn't come...Does this mean low range isn't working and how do i fix this problem:icon_confused:

can anyone tell me how to find out what the factory paint is. I've "decoded" the "VIN" but that didn't tell me!

So this summer i'm beginning on turning my '91 Ranger XLT into a moderately fast street truck but also have show quality. I've already Herculined the bed. Added in-cab LED's, Extra runnings light on rear tailgate and front air dam. Also on the interior I plan to smooth the dash and panels and...