-
Welcome Visitor! Please take a few seconds and Register
for our forum. Even if you don't want to post, you can still 'Like' and react to posts.
the slo-vo build thread...
- Thread starter 86 slo-vo
- Start date
- Joined
- Jan 5, 2009
- Messages
- 4,510
- Points
- 3,101
- City
- owensboro, KY
- Vehicle Year
- 1994
- Transmission
- Manual
yup its a kinker not a tube bender...
read through this youll learn alot:
http://therangerstation.com/forums/showthread.php?t=84561&highlight=jd2+bender
read through this youll learn alot:
http://therangerstation.com/forums/showthread.php?t=84561&highlight=jd2+bender
bobbywalter
TRS Technical Staff
TRS Event Staff
TRS Technical Advisor
TRS Event Participant
TRS 20th Anniversary
TRS 25th Anniversary
Ugly Truck of Month
- Joined
- Aug 9, 2007
- Messages
- 25,511
- Points
- 3,101
- City
- woodhaven mi
- Vehicle Year
- 1988
- Engine
- Transmission
- Automatic
- Total Lift
- sawzall?
- Tire Size
- 33-44
- My credo
- it is easier to fix and understand than "her"
i just invested a shitload of spare time here and there over three days reading this.
hope you keep the 35. errr....35ish
what did frank do for gears?.....cause i would think he would be disappointed going from 488 to 456 if cruise rpm was too high to keep tire size within reason...some axles can get 430 gears which are sweet for 35's and overdrive trans...but 410's tend to be the best for cruising if 488's are too much.
and planting the flowers is ...well your a fag
...though the reasons of keeping vagrants out are valid....
might want to put a bead roll on the fender lips....a cool cost effective hf tool. unless your never gonna work with sheet metal again...
Atlanta sucks to drive through most parts of the day. last time i was through a fine young southern bell relocated my rear axle a little bit for me....after a few hours i had it back on the road
cops in ga definatly care about fenderwells and tire coverage
especially if you have yankee plates.
cant wait to see the bed completion.
as to the hf/princess type bender.....
tube kinker yes.
pipe kinker .... no.
quality pipe properly sized works great. repeating bends perfectly...
not so great...but close enough
hope you keep the 35. errr....35ish
what did frank do for gears?.....cause i would think he would be disappointed going from 488 to 456 if cruise rpm was too high to keep tire size within reason...some axles can get 430 gears which are sweet for 35's and overdrive trans...but 410's tend to be the best for cruising if 488's are too much.
and planting the flowers is ...well your a fag
...though the reasons of keeping vagrants out are valid....might want to put a bead roll on the fender lips....a cool cost effective hf tool. unless your never gonna work with sheet metal again...
Atlanta sucks to drive through most parts of the day. last time i was through a fine young southern bell relocated my rear axle a little bit for me....after a few hours i had it back on the road
cops in ga definatly care about fenderwells and tire coverage
especially if you have yankee plates.cant wait to see the bed completion.
as to the hf/princess type bender.....
tube kinker yes.
pipe kinker .... no.
quality pipe properly sized works great. repeating bends perfectly...
not so great...but close enough
- Joined
- Jan 5, 2009
- Messages
- 4,510
- Points
- 3,101
- City
- owensboro, KY
- Vehicle Year
- 1994
- Transmission
- Manual
i just invested a shitload of spare time here and there over three days reading this.
hope you keep the 35. errr....35ish
what did frank do for gears?.....cause i would think he would be disappointed going from 488 to 456 if cruise rpm was too high to keep tire size within reason...some axles can get 430 gears which are sweet for 35's and overdrive trans...but 410's tend to be the best for cruising if 488's are too much.
and planting the flowers is ...well your a fag
might want to put a bead roll on the fender lips....a cool cost effective hf tool. unless your never gonna work with sheet metal again...
Atlanta sucks to drive through most parts of the day. last time i was through a fine young southern bell relocated my rear axle a little bit for me....after a few hours i had it back on the road
cops in ga definatly care about fenderwells and tire coverage
cant wait to see the bed completion.
as to the hf/princess type bender.....
tube kinker yes.
pipe kinker .... no.
quality pipe properly sized works great. repeating bends perfectly...
not so great...but close enough
thanks man, its been alot of work but its starting to come togather slowly..
franks never has changed his gears...but the 488's with 33's puts him at 3K at 75
the front fenders are ok. they flex a little but over all still pretty rigid...im going to end up bashing them in anyways so when i go exo im ditching them
yea the bender will do fine for other stuff but when it comes to something im wanting to rely on in a rollover...ill stay with the tube bender fast accurate and repeatable bends
I was gonna go to work, but then I got high.
I was gonna clean my room, but then I got high.
I was gonna change my gears, but then I got high.
wait that's not how the song went.
Frank
I was gonna clean my room, but then I got high.
I was gonna change my gears, but then I got high.
wait that's not how the song went.
Frank
- Joined
- Feb 24, 2009
- Messages
- 2,367
- Points
- 3,101
- Age
- 36
- City
- Saskatchewan!
- Vehicle Year
- 1985/91
- Transmission
- Automatic
Frank... you're alive!
Just barely, for now. I'm still working on that
I had to get online to update my phone......... figured I'd see what was up here. I'm sewing wild oats right now (actually I'm on lunch break) gotta get back to the field now.
Truck looks good Jon-Boy.
Everythings going well with other job too.
Ya'll take care now, ya hear. My number hasn't changed.
Frank
- Joined
- Jan 5, 2009
- Messages
- 4,510
- Points
- 3,101
- City
- owensboro, KY
- Vehicle Year
- 1994
- Transmission
- Manual
thanks frank...
got my driver half door done, gunna try and throw some paint on it tomarrow
got my driver half door done, gunna try and throw some paint on it tomarrow
RangerSVT
Oct 09 OTOTM
Article Contributor
ASE Certified Tech
OTOTM Winner
Boosted (Not Stock)
V8 Engine Swap
Solid Axle Swap
- Joined
- Mar 15, 2009
- Messages
- 7,883
- Points
- 3,101
- Vehicle Year
- 19962002
- Transmission
- Automatic
- Joined
- Feb 24, 2009
- Messages
- 2,367
- Points
- 3,101
- Age
- 36
- City
- Saskatchewan!
- Vehicle Year
- 1985/91
- Transmission
- Automatic
hey slo-vo, I got BOTH my half doors done. 
- Joined
- Jan 5, 2009
- Messages
- 4,510
- Points
- 3,101
- City
- owensboro, KY
- Vehicle Year
- 1994
- Transmission
- Manual
yea lol been busy with everything elseWasn't the door half done 3 weeks ago when I was up there??
SVT
hey slo-vo, I got BOTH my half doors done.
yea yea yea, but mine are cooler
RangerSVT
Oct 09 OTOTM
Article Contributor
ASE Certified Tech
OTOTM Winner
Boosted (Not Stock)
V8 Engine Swap
Solid Axle Swap
- Joined
- Mar 15, 2009
- Messages
- 7,883
- Points
- 3,101
- Vehicle Year
- 19962002
- Transmission
- Automatic
Sorry Jon, I couldn't resist the temptation....
SVT
SVT
- Joined
- Feb 24, 2009
- Messages
- 2,367
- Points
- 3,101
- Age
- 36
- City
- Saskatchewan!
- Vehicle Year
- 1985/91
- Transmission
- Automatic
- Joined
- Jan 5, 2009
- Messages
- 4,510
- Points
- 3,101
- City
- owensboro, KY
- Vehicle Year
- 1994
- Transmission
- Manual
already beat ya hoss....
Sponsored Ad
Sponsored Ad
Special Events
TRS Events
Member & Vendor Upgrades
For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.
Latest posts
-
-
-
-
-
-
-
TRS Event 2025 TRS Fall Colors Campout- Latest: Curious Hound
-
Recently Featured
TRS Latest Video
TRS Merchandise
Follow TRS On Instagram
