Tech section links

[1986RangerXL]

Under 'Engine Rebuild' in the tech section, '3.0 Rebuild' just directs me to the article on building a 4.0 for power

 

[Uncle Gump]

Maybe it's trying to tell you something? lol

I'm sure that is not the case. Going to take a look...

 

[Uncle Gump]

@Jim Oaks

There is a linking issue as described above.

 

[Jim Oaks]

Sorry. Fixed it.

Ford 3.0L Build - The Ranger Station

The 3.0L Ford pushrod motor has been around for nearly 20 years. It was originally introduced back in 1986 and millions of them have been installed in a wide variety of front and rear wheel drive cars and trucks since … Continued

www.therangerstation.com

 

[Curious Hound]

Sorry. Fixed it.

Ford 3.0L Build - The Ranger Station

The 3.0L Ford pushrod motor has been around for nearly 20 years. It was originally introduced back in 1986 and millions of them have been installed in a wide variety of front and rear wheel drive cars and trucks since … Continued

www.therangerstation.com

And you got it before any really bad postings about “replacing with a 4.0l” is the best way to rebuild a 3.0l.

Thank you

 

[1986RangerXL]

Maybe it's trying to tell you something? lol

I've got the 2.9, I feel bad for those w/ the 3.slow

 

[Uncle Gump]

And you got it before any really bad postings about “replacing with a 4.0l” is the best way to rebuild a 3.0l.

Thank you

I'm pretty sure I addressed that in post 2...

 

[Curious Hound]

I'm pretty sure I addressed that in post 2...

Yes. But you did it nicely and quietly. An elegant understated style.

 

[Uncle Gump]

Yes. But you did it nicely and quietly. An elegant understated style.

If been reading all RonD's posts... he might be rubbing off of me.

 

[1986RangerXL]

Trying to find out how to pull codes..
"Engine and Fuel Systems"
Under "Engine Rebuild"
"Basic Engine Troubleshooting" goes nowhere. Just me?
@Jim Oaks

 

[Jim Oaks]

I'm changing the file structure of the site since adding a 2019 Tech Library. Lot's of work. Still in progress.

Here's the page you were looking for:

https://www.therangerstation.com/tech/basic-engine-troubleshooting/

If you're looking to pull codes, you're probably looking for:

Testing EEC-IV Equipped Engines - The Ranger Station

The EEC-IV equipped engines use an older diagnostic system to monitor and report engine related malfunctions. This system is known as On Board Diagnostics (OBD-I). The Diagnostic Trouble Codes (DTC’s) are two or three digit numbers and can be … Continued

www.therangerstation.com

OBD-I Diagnostic Trouble Code - 2-Digit Ford Codes - The Ranger Station

Differences in test mode noted as: (O) = Key On Engine Off test (R) = Key On Engine Running test (M) = Memory code Code Definition 11 System checks OK 12 Idle Speed Control motor or Air Bypass not … Continued

www.therangerstation.com

OBD-II Trouble Codes - The Ranger Station

You’ll need a Code Reader to read the trouble codes. DTC Codes – P0100-P0199 – Fuel and Air Metering P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow … Continued

www.therangerstation.com

OBD-I Diagnostic Trouble Code - Ford 3-Digit Codes - The Ranger Station

Differences in test mode noted as: (O) = Key On Engine Off test (R) = Key On Engine Running test (M) = Memory code Code Definitions 111 System checks OK 112 (O,M) Intake Air Temperature (IAT) sensor is/was low … Continued

www.therangerstation.com

 

[1986RangerXL]

Thanks

 

[sgtsandman]

Don’t forget to eat from time to time.