2 piece Dana 35 ujoint and ds support bearing sanity check

[jballard81]

After an embarrassingly long amount of time reading and rereading the service manual, I'm pretty sure I found the correct replacement ujoints and driveshaft support bearing, but would appreciate confirmation before i place my order. going on a 94 ranger 4x4, 8.8 rear axle.

so the driveshaft support bearing has a spicer replacement option: DANA 2115901X

earing Id (IN) A	1.181
Bracket Width (IN) C	1.310
C-L To C-L (IN) D	5.880
Cl To Mounting (IN) B	1.940
Series	1310
Style	11

This one appears to be greaseable. not sure if that is preferred or not. i would imagine so...

then i would need 3 ujoints: DANA 513101X

Bearing Cap Diameter (1) (IN)	1.062
Bearing Cap Diameter (2) (IN)	1.062
Bearing Cap Diameter A (MM)	1.062
Bearing Cap Diameter B (MM)	1.062
Bearing Cap Finish	Ground
Bearing Cap Type	Round
Bearing Cap Type A	OSR
Bearing Cap Type B	OSR
Coating Type	None
Grease Fitting Location	One lube fitting in bearing
Grease Type	N.L.G.I. Grade 2
Grease Zerk Included	Yes
Greaseable	Yes
Hardware Included	No
Length A (IN)	3.219
Length A (MM)	81.8
Length B (IN)	3.219
Length B (MM)	81.8
Material	Steel
Model Number	SPICER 1310/SPL22
OEM Mfg	SPICER
OEM Series	1310/SPL22

thanks in advance!

 

[antman]

sorry there are no responses , for us both.
I have been given the wrong ones,

apparently there are 2 cap dia's 1 1/16" and 1 3/16" i need the larger, still not certain though and looking for clarification.

 

[jballard81]

for my 94 with 4x4, i believe i ended up going with the Dana 5-1310X for the 3 ujoints. Carrier bearing PN: HB88107A
cheers!

 

[scotts90ranger]

Yeah, I'm not up on part numbers or I probably would have helped before...

The auto parts stores have jumbled data on front axles and a bunch of stuff, mid '90 to '97 is always the bigger U joints and wheel bearings and stuff... they seem to think that Explorers had a Dana 28 at some point which never happened...

 

[antman]

Happy to have a masters in ujoints series and cap dia to find out my ranger has 2 1350 series 1 3/16 cap dia at each wheel
And 1 1310 series in mddle which i havecnot seen anywhere ?

 

[Curious Hound]

Happy to have a masters in ujoints series and cap dia to find out my ranger has 2 1350 series 1 3/16 cap dia at each wheel
And 1 1310 series in mddle which i havecnot seen anywhere ?

There is a mod some people have done that uses D44 outer end parts on the D35 axle assembly. I wonder if someine previously did that on your truck and you may find other parts that are different.

 

[Jim Oaks]

I'm confused by what you guys are trying to figure out. The U-joints in the Dana 35 shafts are 5-760.

https://www.therangerstation.com/tech_library/pdf_documents/dana_spicer_axle_part_number_catalog.pdf

D1 BEARING CAP DIA:1.188
D2 BEARING CAP DIA:1.188
K1 SNAP RING DIM: 2.188
K2 SNAP RING DIM: 2.188

 

[Curious Hound]

I think mine are the 5-760x which has the groove for the retaining ring to go inside the ears of the yokes. It crosses to the standard 1310 size. I believe there is also a regular 5-760 joint.

 

[bobbywalter]

greasable non greasable.


those are 760 joints. dana 44 or 35.

the op for rear shaft is either 1330 or 1310.