Escorts 2nd SAS

[88_Eddie]

that's the good thing about 30's, i know of three HP 30's down here for less than $100

 

[escort_gts]

that's the good thing about 30's, i know of three HP 30's down here for less than $100

Very true.
But, if/when this axle goes....it goes.

Sent from my HTC ONE using Tapatalk!

 

[dangerranger83]

Very true.
But, if/when this axle goes....it goes.

Sent from my HTC ONE using Tapatalk!

Right into the bed of my truck.

Sent from my rooted SPH-D710 using Tapatalk 2

 

[buell-eyed-devil]

kinda why I like the idea of a 30......salvage yards are full down here as well

 

[escort_gts]

Right into the bed of my truck.

Sent from my rooted SPH-D710 using Tapatalk 2

You can have it, but when that time comes, its time for 60/sterling!!!

Sent from my HTC ONE using Tapatalk!

 

[dangerranger83]

You can have it, but when that time comes, its time for 60/sterling!!!

Sent from my HTC ONE using Tapatalk!

And I will be sure to remember that too.

Sent from my rooted SPH-D710 using Tapatalk 2

 

[Josh40601]

super dooty axles can be snagged relatively cheap. There was a guy here locally that was selling the transfer case, front and rear axle with 4.10s for 500 bucks. If I had the money at the time, that stuff would be going under D.

 

[88_Eddie]

i cant decide what to do. grab a 44 and start collecting parts to narrow/install it or just keep buying used crap for the 30.....or maybe just build another 4x4 to beat on since i'd like to keep the b2 nice

 

[kris97ranger]

Id do like josh said super duty axles on leaves. They fit waaaay too well and even though they are still unit bearings its meant for a much heavier truck so you should be fine.

Never really understood the dana 30 sas every one i see ends up bent and eating bearings.

 

[escort_gts]

The Dana 30 was a cheap and easy swap for me. And for what I use the truck for is perfect.

And for the 1ton axles, I can get a set from a superduty for $250 a set. Just need to play the waiting game and watch the take-a-part for them to come in.

Sent from my HTC ONE using Tapatalk!

 

[Josh40601]

The Dana 30 was a cheap and easy swap for me. And for what I use the truck for is perfect.

And for the 1ton axles, I can get a set from a superduty for $250 a set. Just need to play the waiting game and watch the take-a-part for them to come in.

Sent from my HTC ONE using Tapatalk!

Hell yes. Find me a set too!

 

[Josh40601]

i cant decide what to do. grab a 44 and start collecting parts to narrow/install it or just keep buying used crap for the 30.....or maybe just build another 4x4 to beat on since i'd like to keep the b2 nice

TJ rubicon 44 with RCV or Yukon shafts and an ARB. best setup for retaining the 5x4.5

 

[escort_gts]

TJ rubicon 44 with RCV or Yukon shafts and an ARB. best setup for retaining the 5x4.5

And most expensive way.

Sent from my HTC ONE using Tapatalk!

 

[Josh40601]

And most expensive way.

Sent from my HTC ONE using Tapatalk!

yes. lol

I don't know any other axles that retain the 5x4.5 outside the turdy and the TJ rubi 44

 

[escort_gts]

yes. lol

I don't know any other axles that retain the 5x4.5 outside the turdy and the TJ rubi 44

I don't know of any others.

Sent from my HTC ONE using Tapatalk!