RockRangerII refresh

[alwaysFlOoReD]

Great use of your talents. I like both the fold up wood cabinet and the press brake.

 

[RockRanger]

Thanks. I can't sit around and watch tv all day. I need projects to keep me busy.

So decided to do this yesterday. I sure like my floorjack spacers. Unbolted the bumper put the jack under it with a set of vice grips clamped to it and dropped the bumper. I have the bumper still balanced on the floor jack as I move it around the garage.

20170202_110415 by Matthew Dresselhaus, on Flickr

20170202_121442 by Matthew Dresselhaus, on Flickr

As far as I got so far.

20170203_142040 by Matthew Dresselhaus, on Flickr

20170203_142048 by Matthew Dresselhaus, on Flickr

 

[Jim Oaks]

That cook box looks like it's going to turn out pretty nice. Post some pics when you get to try it out.

 

[Grunizzle]

dude, looking good I want to see where this goes! I wish I had a plasma table. I still love my console BTW

 

[RockRanger]

Glad you like it. I like mine as well. I got more done on the bumper. I still need to finish it.

20170205_100917 by Matthew Dresselhaus, on Flickr

20170205_101232 by Matthew Dresselhaus, on Flickr

20170205_101513 by Matthew Dresselhaus, on Flickr

20170205_104401 by Matthew Dresselhaus, on Flickr

20170205_104350 by Matthew Dresselhaus, on Flickr

20170205_104421 by Matthew Dresselhaus, on Flickr

 

[Rowdy Fitzgerald]

Is that a new bumper or did you modify the old one? If it's a new one, I'll buy your old one.

Sent from my SM-G930V using Tapatalk

 

[RockRanger]

Yes it is a completely new bumper. Shoot me an offer on the old one. It will be available after March 7. I am going on the Kingsburg snow run that weekend. If I don't finish the new one in time I plan to put the old one back on.

Sent from my SM-G920V using Tapatalk

 

[Rowdy Fitzgerald]

Ok will do, I'm getting ready to start back with cal fire so I'm gonna go a month with out a pay check. I should get a check on April 1st.

Sent from my SM-G930V using Tapatalk

 

[RockRanger]

Old Bumper next to new one.

20170303_111544 by Matthew Dresselhaus, on Flickr

20170303_111551 by Matthew Dresselhaus, on Flickr

Got the new one installed.

20170303_153719 by Matthew Dresselhaus, on Flickr

20170303_153730 by Matthew Dresselhaus, on Flickr

Took a little cutting to get the winch to fit.

20170303_151655 by Matthew Dresselhaus, on Flickr

Takes all of my 60 inch hillift to barely get a front tire off the ground. Normally I would chain the suspension but wanted to see what it would do.

20170307_111310 by Matthew Dresselhaus, on Flickr

 

[Curious Hound]

Very, very NICE!

 

[Grunizzle]

dude badass bumper!

 

[RockRanger]

Last week I had a down day so I headed up to the snow to play around a little. I also just got a gopro knock off camera so I did a little filming and editing and made a quick video.

https://www.youtube.com/watch?v=lXxJ6IBct_w

Today I decided I needed a way to warm up some food on the engine. I could never figure out a good spot on the 4.0 that would be easy to place and then pull off a hot engine some food. After looking under the hood I found a large open area due to not having A/C on my truck. I figured I could do something there. On the passenger side exhaust manifold there are two threaded bolts facing up. The rear one holds the coil pack bracket and the forward one is empty.

20170317_134441 by Matthew Dresselhaus, on Flickr

A bit of time measuring, drawing on the computer and then plasma cutting I had all the parts cut. A few key welds and some bending the parts were ready.
20170317_134407 by Matthew Dresselhaus, on Flickr

Then the bracket is bolted to the two holes in the manifold.

20170317_145630 by Matthew Dresselhaus, on Flickr

Next the inner tray is dropped in. I made it removable so that it could be easily cleaned and to make installation easier.

20170317_141856 by Matthew Dresselhaus, on Flickr

Then drop the lid on and latch it shut.

20170317_141846 by Matthew Dresselhaus, on Flickr

Now I need to go on a wheeling trip and try it out. In total it sits about 2.5 inches above the exhaust manifold. Hopefully that is close enough for it to get warm enough.

 

[Rowdy Fitzgerald]

That food box is a fantastic idea!

Sent from my SM-G930V using Tapatalk

 

[Grunizzle]

Any tests on the food warmer yet?

 

[RockRanger]

Yes. Tossed two hotdogs wrapped in tinfoil in it for about an hour. Pulled out some warm hotdogs. Could have been a bit warmer but still tasty for something wsrm on the trail. I spent most of the time just cruising on some forest service roads. The big test will be in two weeks. Taking the truck on a 1000 mile round trip run to death valley and the eastern side of the Sierra Nevada mountains.

Sent from my SM-G920V using Tapatalk