motor mount plates

[joey7478]

I don't want to piss anyone off because this has probly been ask a dozen times.The tech artical doesn't give the the exact measurements. Need measurement for motor mount plates for v8 in 1999 ranger coil spring supenion. THANKS! Joe

 

[RangerSVT]

The bolt pattern is 7" apart for the block, and the motor mount stud is 1.5" off the perpendicular line from the block. The driver side needs to be lifted about 1.25" higher than the passenger side to level the motor. I can a set if you need em...


SVT

 

[joey7478]

The bolt pattern is 7" apart for the block, and the motor mount stud is 1.5" off the perpendicular line from the block. The driver side needs to be lifted about 1.25" higher than the passenger side to level the motor. I can a set if you need em...
How much for them and how much to send to Ohio? Thanks! Joe 45784

 

[Mac]

Teddy posted these on another site. Believe it's the passenger side that gets raised but only 1/2".
Dave

 

[RangerSVT]

Thanks for the pic, Dave. I didn't have it on hand to post. Joey, I make em for $30 shipped. I have a couple members on here that bought a set and there very happy with em...


SVT

 

[Scott B.]

Joey,

I have a set of 4.0L engine mounts if you need them.

These are brand new - I was going to use them with plates, but ended up using different engine mounts.

 

[Mac]

Thanks for the pic, Dave. I didn't have it on hand to post. Joey, I make em for $30 shipped. I have a couple members on here that bought a set and there very happy with em...
SVT

Just wondering how close you duplicate them. I know others have gone with out the gussets and gone to a thinner, not as strong steel. $30 sounds really good. I always seem to get questions about the plates, Got a good contact number I could pass on? Those are what I converted BrianB's drawings from metric and to a common steel. Ever need the .dwg files, just giive a shout.
Dave

 

[RangerSVT]

I use flat plate, usually 5/16 or 3/8, and on the block bolt side I use 1.25" solid round stock with the center drilled and then welded to the plate. I'll dig for some pics....

SVT

 

[Mac]

I use flat plate, usually 5/16 or 3/8, and on the block bolt side I use 1.25" solid round stock with the center drilled and then welded to the plate. I'll dig for some pics....
SVT

Would appreciate that, having a hard time picturing what you describe.
Dave

 

[RangerSVT]

Dave, I couldn't find any pics, but maybe stickshift will chime in with a pic of his. He has the last set I made...

SVT

 

[joey7478]

Joey,

I have a set of 4.0L engine mounts if you need them.

These are brand new - I was going to use them with plates, but ended up using different engine mounts.

how much for the mounts and shipping to ohio? Thanks! Joe

 

[Scott B.]

how much for the mounts and shipping to ohio? Thanks! Joe

Here is a link to the For Sale thread (with picture) on ExplorerForum: Link

To answer your question - $20.00 gets them shipped to you.

 

[RangerSVT]

Dave, I just got the pics. Here they are...


]

SVT

 

[joey7478]

still have mounts

Joey,

I have a set of 4.0L engine mounts if you need them.

These are brand new - I was going to use them with plates, but ended up using different engine mounts.

Do you still have mounts and how do I pay you? the explorer site say they are for 4x4 will they work in 2 wheel drive? Thanks Joey!

 

[RangerSVT]

You can paypal me and I'll send em out to you...

SVT