Search results

Put some lights on my bumper and can't find a good place for the switch and wire to enter the cab. Where have you run the wire?

On my ranger, the PO put in a dual exhaust and it's rotted to hell and has a bunch of rust hols formed or forming. Looking at replacement exhausts, should I just go back to stock single exit? If so, do I need to do anything else to like the cat or can I just bolt right up? Or should I stick with...

2000 2wd Ranger. Recently had new tires put on, and since them have had them rebalanced and one replaced (faulty tire was out 12 ounces). Drove with the window down for the first time in a while and noticed a sound like there was a rock in my tire... kind of a clicking? Sounds like it's coming...

Did a lift on my 2wd ranger that requires adjustable camber bolts to get a proper alignment. My dumb ass ordered two bolts- forgetting that EACH side needs two bolts. So right now one side has adjustable, one side has stock. Drove it down the block and it's wobbling BAD. I just stopped and...

So as of now my high beaks work but not my regular headlights. Changed the bulbs, cleaned the terminals, checked the fuses, all should be good. The other lights work. Any thoughts on what that could be? Also, I have a soft-ish brake pedal. It's kind of always been that way, and I'm wondering...

Used search and read a lot of threads about this but a lot seem to talk about what comes stock on particular models. With a 2000 2WD which would you install? Doing spindles up front. I already ordered 2" longer shocks as if I were using blocks, would I use the same longer shocks for shackles or...

OK. So I think I'm going with a 4" spindle (front) and 2" block (rear). Also want to get new 32s. I have new wheels sitting here in the box. I figure I should wait to mount the wheels until the lift is done, then do tires/wheels all at once? Doubt I can clear 32s on stock set up right now. Also...

Thinking of adding some inches to my 2000 2WD. I've never done a lift and am wondering what my best options are according to the more experienced folks. I'm about to replace some suspension parts (shocks, control arms, ball joints, etc) and figure it's reasonable to do the lift at the same time...

I have a 2000 2WD and don't go mudding or off roading but do occasionally take the back roads to go find trails. The truck handles fine, but I still wonder what upgrades I could make so that it's happier. Shocks upgrade I'm assuming? What else?

Just started hearing a single click like noise when applying brakes. Sounds almost like it's coming from the pedal? I checked the calipers- they're snug (though we're loose last week but I retightened them). Just redid the calipers pads, rotors and had the brakes bled. Any thoughts on what this...

Well I've blown up just about every other nook and cranny of this forum with silly questions and figure I should just compile the progress into a little build thread. Bought this about a month or so ago, 150,000 miles. It had been sitting for a year but started right up with a jump and has had...

I feel like I rarely see Rangers (older than 1999) with two-tone paint jobs, stripes, anything like that. The body doesn't have the same lines/breaks as the older models, but I'm curious what some non-solid paint jobs look like on newer models. Anyone do anything like this to their truck?

Driver side front 2000 ranger. Just replaced wheel bearings pads rotor and caliper. Now when I apply brakes at a slow speed there's a single quiet clunk noise. Caliper loose? Ball joint going? Some other suspension issue? Safe to drive until I get it to a shop or stop immediately??? I'm on an...

Replaced my grill today and noticed this when I took off the old one. Welllllll bummer. Popped the hood and took a look from the top Lemme guess- frame is shot? needs to get weld repaired? I don't even know if I should be driving on this.

Super frustrated on many levels, thinking I picked a stupid hobby that I'm not cut out for. So maybe last post. Went to replace my window motor because the window left a gap when rolled all the way up. Got it all done and good to go- last fastener to attach window to motor arm- glass ****kng...

Here it is as it stands (and my other projects peeking out in the first picture) What I'd like to put on are fender flares- either: black or chrome Bed rails, either: black or chrome or diamond The tailgate rail is already black... and maybe a silver bull bar? Or black? I just...

I'm assuming because I was a dummy and didn't pinch the brake line that there's air in my brakes. How do I fix this? Bleedbthe brakes? I've never done that- easy enough or is it a complicated task? Thanks!!

Would love to throw some black fender flares on here but the only ones I see online are for the trucks with predrilled holes for the flares. Can I just drill holes? Or do they make flares without the holes and I just can't find them? Thanks! PS This is where it'd been parked for a year when...

Got new tires today and they let me rock the wheels while it was jacked up. Passenger wheel didn't budge, driver wheel had very slight left-right play. Like, a fraction of a centimeter, but it still moved. I'm assuming something needs to be replaced- ball joints? How do I tell how bad it is...

Driver window leaves 1/2" gap when rolled up; passenger door power lock doesn't work Power window on my 2000 Ranger, when I roll up the driver window there's a 1/2" gap left- it doesn't roll all the way up. My girlfriend encouraged the window up from outside the car while I was inside holding...