• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

What did you do to your Ranger today? (Part Deux!)


not many benches is why i thought you didn't get many spectators
 
Changed the rear differential gear oil on the 2011.
 
my son is daily driving the cool guy ranger for now. his focus needs new struts because they locked in the full up position so its like driving a wagon around
 
I changed front struts (complete units with springs) and rear shocks on an '02 Focus in like an hour and a half, parts were stupid cheap too, this was like 9 years ago though...
 
its still the same way. he just doesn't have money to buy new stuff yet because he wants to put bilsteins or konis in
 
its still the same way. he just doesn't have money to buy new stuff yet because he wants to put bilsteins or konis in

Locked up how? Like.. siezed extended?


Highly reccomend the konis, especially if he has/wants to lower the thing. The adjustability of the konis with stiffer springs is really nice 👌
 
yes, seized upwards.

i told him konis too. i had them on my 89 325i for autocross with coil overs and they were awesome. to me, konis are better than bilsteins. (i have bilstein 5100 on my truck right now)
 
Pressure washed about 20 lbs of Kentucky and Indiana mud off the bottom of it. Left it on the trailer and backed it unto the yard. Might do a night ride at the local park next week. Then, going g to Kentucky again October 20-23 for "Overland The Red". An event being put on by Northology.

 
not many benches is why i thought you didn't get many spectators
Unfortunately those damn bleachers are super expensive and barely used even with a big crowd so we didn't add any more in the 6 years since we built the track. We've found most spectators are either roaming the pits, leaning against the pit side fence or sitting in lawn chairs in their truck's box backed up to the fence on the other side. We're also in a fairly low population area of the Province so we don't really have access to the big crowds like you guys south of the border.
 
Our little spring rate tweak to the rear leaf spring pack raised the truck a couple of inches but both the pinion angle and the CalTracs bottom bar angles are waaaay better now. First time trial tomorrow morning will tell if it worked or not.......

20220916_102929.jpg
 
Started work on prepping the engine bay, probably one more day at most of that and I’ll be ready to set the engine and trans.

Also blasted most of my engine hoist with some fresh rattle can because it was looking pretty rusty. I have a brand new engine leveler here now too. My old one hasn’t appeared yet, pretty sure it’s waiting for me to get the new one dirty first. Did take another half-hearted look around for it though.
 
Started work on prepping the engine bay, probably one more day at most of that and I’ll be ready to set the engine and trans.

Also blasted most of my engine hoist with some fresh rattle can because it was looking pretty rusty. I have a brand new engine leveler here now too. My old one hasn’t appeared yet, pretty sure it’s waiting for me to get the new one dirty first. Did take another half-hearted look around for it though.
in a few weeks when your looking for something else you can't seem to find and there it will be.
 
in a few weeks when your looking for something else you can't seem to find and there it will be.
I was trying to make it show itself before I forever spend the money on another. Just not too many reasons for needing two engine levelers at once and they don‘t exactly give them away. But yeah, I’m expecting it to show up sometime after I can’t return the new one
 
I was trying to make it show itself before I forever spend the money on another. Just not too many reasons for needing two engine levelers at once and they don‘t exactly give them away. But yeah, I’m expecting it to show up sometime after I can’t return the new one
Who has only one of a tool? The more you have the easier it is to find one...isn't it?
At least thats what I tell myself to justify the 7-8 hacksaw,4 mini grinders, 5 18inch pipe wrenches, 4 compressors and on and on
 
Who has only one of a tool? The more you have the easier it is to find one...isn't it?
At least thats what I tell myself to justify the 7-8 hacksaw,4 mini grinders, 5 18inch pipe wrenches, 4 compressors and on and on
Oh it’s easy to justify multiples, I learned the real value of that when I bought a two pack of grinders because it was on clearance (should have bought the other two boxes of them then too), but I started with putting just one into service and figured I’d have the other as a spare which lasted right up until I’m switching between a cutting disk, grinding disk and wire wheel and said this is stupid and got out the other new grinder. I just don’t see myself using an engine leveler like that, lol
 

Sponsored Ad


Sponsored Ad

Overland of America

TRS Events

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Our Latest Video

TRS Merchandise

Follow TRS On Instagram

TRS Sponsors


Sponsored Ad


Sponsored Ad


Amazon Deals

Sponsored Ad

Back
Top