I've seen a couple threads where people have upgraded pre-1995 RBVs with newer M5OD-R1HD trannys. I like the idea of the lower 1st & 2nd gear, but even after a few hours of reading, I'm sort of confused. I've yet to find out how these guys are making their speedometers work. From what I've...
Ok, my truck started spilling fuel from the Fuel Accumulator canister. I guess thats what its called, at least thats what I've read. Any how, I've attached is a example photo of the thing. So, since I've already replaced the in-tank pump with a Walbro 190 and detached the 2nd frame rail pump...
Sorry if this has been discussed. I have to work later tonight and I don't have time to do the research.
Anyway, I found a 2nd Gen Explorer with a 4.0 OHV engine, its got a ceramic/black plastic intake. So, I'm not certain of the exact year of the truck but it is a push rod motor. after a quick...
Hey guys, so I've not seen any 4.0 swap threads that explain what to do after swapping a Ranger harness then correcting the brake light/power window issues. *Please link a thread if there is a full write up*
Anyway, that issue has lead me to investigate alternative methods of doing the 4.0...
I'm wondering if I can swap my 90 BII dash with a older model dash. I like how the old dash allows for quick heater core replacement. It took me about 10 minutes to put a new heater core in my 88 Ranger. :D
A guy on Craigslist has a 87 Ranger with about 3.5" suspension lift so I'm wondering if the kit will fit my 90 BII ? I know the 87 Ranger should have a Dana 28 but my 90 BII has a D35. Just wondering if the drop bracket and all will interchange.
Doing a Mustang Intake swap on my '88 Ranger 2.3L with the relocated Idle Air Control Valve. While doing so I pulled these 2 little vacuum switched solenoid things loose from my inner fender. They were held in place with a dry rotted rubber mount. The 2 vacuum lines (Red & Green) are...
To begin with I know my roof seams are busted and caused my roof liner to get wet. I started taking all the interior out and found some new areas of interest. Both kick panels are currently wet. The back of the computer was starting to rust. I also noticed some foam inserts in the both kick...
Hey guys.
I'm thinking of buying a 87 Ranger but the front Turn Signal Panel is beat up bad. Does that panel come off with house hold tools or will it require a shop and or welding ?
I'm reasearching the Explorer front driveshaft modification (u-joint) for my 1990 Bronco II.
I need to know if the "Front" Driveshaft Slips are interchangeable from 1st Gen to 2nd Gen.
I keep finding several guys with the earlier models BIIs that have no problems switching the entire front...
Duh, sorry about the topic typo. I meant conversion.
Anyway,
What needs to be done to swap out the 88 Fuel Injection to a Carburetor set up ?
Please don't ask why because I will not answer. I've heard enough criticism lately. :thefinger: I just need to know what has to be done and...
I just got a late model 2.3L header from a 96 Ranger. I got the header from a junk yard but it did not come with bolts. There are spacers on the mounting holes that are about 1.5" long. My concern is, were the fasteners actually studs or just plan bolts ?
Does anyone have a source for these...
I just bought a 90 B2 XLT.
This is my #4 spark plug. The rest of the plugs are fine. It still has a miss-fire after all new cap/rotor,wires, and motorcraft plugs. The exhaust is not smoking, yet. I'm thinking I have a bad injector dumping too much fuel.
What do you all think ?
Hey guys.
Sorry to speak of another forum if that bothers any of you. Anyway, I've tried to register at broncoii.org and I'm supposed to recieve a email after the admins review my info. Its been several days now and I still have not recieved any word from them. I'm just wondering if that site...
Hello everyone that took the time to look at this thread. I dont have a Ranger and I cant seem to find a picture of a belt driven radiator fan for the Ranger 2.3 so I'm asking the experts here. My Ford T-Bird 2.3 Turbo came with dual electric fans and its running hot after a 3 row aluminum...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.