Search results

I've had a Sigma 40 and now own the XD 40 and the XD is a much better pistol. The Sigma's trigger, at least the one I owned, was horrible. I think the trigger pull is between 10 - 15 lbs. From what I understand, you can't lighten it up much either. Otherwise, it was a nice pistol.

I somehow have contracted a case of ants inside of my truck. Would it be ok to set off one of those fogger deals, inside the cab? :annoyed:

Has anyone else had problems with the driveshaft that goes from the t-case to the front axle? It appears to be a 2 piece shaft and has broken free on the inside. This is the second time it has happened. The replacement shaft came from a junkyard, no telling how many miles were on it to begin...

Have any of y'all had the heat shield on the front of the gas tank come loose? How did y'all fix it? Thinking of trying some kind of glue and a short piece of rubber hose to attach it to the gas tank itself. Sounds like one of the skid plates is about to fall off of the damn thing when you...

I have what appears to be a main bearing seal leak but it doesn't leak all of the time. It seems to only leak when I go on long drives or pull my 4 wheeler/trailer to deer camp. It's not a horrible leak or anything, just a few drops here and there. I just had the valve cover gaskets and oil pan...

Around here, we skip straight to this part.:icon_rofl:

Thanks for the offer but I'll have to pass. They are all paid for and like women... it's cheaper to keep them.

I've had enough of oil/coolant leaks. My wife's car had a leaking valve cover, my 4 wheeler has had two seals blow, my mower has an oil leak, my truck had a valve cover leak and now it has another oil leak, also had a coolant leak to go with the valve cover leak. I am just about ready to trade...

I realize that they can be temperamental but not nearly as bad as what chknfkr was making them out to be.

Say what? I have an AR15 and have never had a FTE or FTF. Several of my friends have AR10 and AR15 rifles and never have a problem with them.

110v ac to 12v dc converter. I have an ATV winch that I want to use as a hoist, in our deer skinning shed, and want to tie it into a converter and then use it to plug into one of the wall outlets. Any suggestions?

Since I replaced the transmission, in my truck, I haven't driven more than 10 miles in one trip... until yesterday. We took it on a 30ish minute drive, to a friend's house, and it did fine on the way over. Once there, I helped him move some stuff out of his yard, to the pasture behind his...

that the engineers that designed the 4.0 and the ones that figured out how to place it in the truck, should be beaten. :icon_rofl: I think they successfully designed that engine/compartment to be a pain in the butt to work on. From the PCV valve to the thermostat to the tensioner pulley, all 3...

Had the new transmission installed but the guy who did it, didn't install the filter I bought. He didn't drop the pan to see if one was installed because it had a new gasket already on the transmission. How would the transmission "act" if the filter wasn't installed? Would it operate correctly...

Is there a gasket between the transfer case and the transmission in a 2001 Ranger with the 5R55E transmission? I was just looking at the transmission, that I received Monday, and it looked like there was a little bit of gasket material on the face of the tail housing.

ATF fluid, is it worth using in a re-manufactured AT or should I go with something else?

it was time for some new ball joints in my truck. :icon_rofl: The steering felt fine but one day I noticed that the tires were leaning out, on the bottom. It also had developed a squeak when I'd turn the wheel while stationary. Put the bottom ball joints in, on both side, and it's like...

That would be legal in MS. In fact, it'd probably be a helluva conversation starter. :D

Here lately my transmission has been shifting hard from 2nd gear to 3rd gear and 3rd gear to 4th gear. Yesterday, it was pretty bad but this morning it shifted like when it was new. It's not slipping... just shifting very hard. It's full of fluid and the fluid looks nice & clean, doesn't smell...