Recent content by Syko

Another custom long arm build hah.. I got a little ahead of you guys so ill catch you up. My plan is to swap the entire TTB axle in with extended arms, Ill be swapping over the knuckles over because they have new ball joints in them. Also using the stock radius arm mounts mounted back on the...

1991 Ford Explorer Sport. 296k Has a miss while accelerating, and a rough start in the mornings. First start of the day the engine fires right up but shakes for a good 30-45 seconds before it calms down and I can drive. Traveling at highway speeds or up hills is when I notice the miss the...

94 Exploder 5.5 super lift with soa and 2 inch extended shackles. I was gonna post the pic in the tread but they turned out gigantic. Heres a link to my Album http://imgur.com/a/sE4L5

Had some free time this weekend so I finally got around to doing something. I installed 3 washers each side at 1/8 a piece, just enough not to notice the \----/ lol... Before: After: The washers: Some poser shots :headbang:

I bought a 1994 Ford Explorer Sport for my DD, so I can have my bronco II as my full time wheeler. BUT I can't help myself to see what she can do :headbang: Some beauty shots and a vid of my 87 Bronco II :icon_hornsup: Older video but a good one showing off the ONLY Ford in about 20...

Stock 1987 Bronco 2 w/ electronic TC, both indicator lights stay on constantly, but its actually in 2wd. Heres what happened. I put the bronco in 4low so it wouldnt roll anywhere while i jacked up the rear to remove the sway bar. i finish up and go to go for a test drive, it wont come out of...

I bought myself an 1981 Monte Carlo with a 350 in it for 1500 bucks, shes going to be my daily driver until i get the clutch in the bronco2 fixed. The 350 Its got a brand new duel exhaust I know its not an RBV or ford... but i couldnt walk away from it Syko

I went wheeling! I think i need a locker lol New muffler.

1987 B2.. the 2.9 started to what feels like a miss once in a while.. which really started to bug me soo the first thing i did was unplug the EGR and took off the vacuum line and plugged it then disconnected the bat for 30 mins.. since disabling the EGR the engine started to run good.. im just...

Basically everyone I know has told that these things roll really easy (not any of them have driving a b2 besides mine maybe once).. Ive owned an 87 b2 for about 2 years now and do very mild offroading and not once did i feel like i was going to go over.. maybe i 4x4 it hard enough but I actually...

Original Poster: Syko Difficulty: 3 out of 10 Time to install: 20-45 mins Disclaimer: The Ranger Station.com, The Ranger Station.com Staff, nor the original poster are responsible for you doing this modification to your vehicle. By doing this modification and following this how-to you, the...

Okay, my engine (2.9) runs fine at idle but as soon as i start going anywhere it starts to bog down at a sertin point on the gas peddal like its not getting enough gas and if i give it alot of gas the engine will stall. not to sure whats going on. My guess is a fuel filter, there might have been...

Just wondering whats a safe temp.. since its gotten really hot out my engine gets up to about 190. just worryed about cracking a head. Thanks, Syko

When I stomp on it I only bring my 2.9 up to about 4,500 rpms before i shift, am I driving my bronco like a girl?? Dont have a stock tach but I do have an after market tach so im not to sure what the redline is.. How high do u guys rev ur 2.9's? Thanks, Syko

Ive got some bad vibrations under hard acceleration could that be the results of a broken knock sensor?? Im pretty sure its broken too.. Thanks Syko