xlt

Hey all. I’ve lurked around here on and off for years, consuming your combined wealth of knowledge on Rangers whenever I needed it. But it seems it’s finally time for me to start my own thread. I’m looking to get new wheels and tires for my 06, and having a hell of a time understanding what...

So I found a radius arm bushing for sale on the marketplace. I'm hoping it will fit my "97" XLT 2WD 3.0 but I can't be too sure but I figured someone on here would be able to help me out. Thank you again in advance. #b3stforumever

Hey yall! I am going to install 4.10 gearing into my 91 Ranger with Dana 35 TTB. Currently have 3.73s, I think I can use my existing carrier? I have read that there is not a “carrier split” so I should be good? Thanks

Just wanted to show yall my 1991 Ranger 4x4 I bought the other month. It’s a 2.9l v6 152,000 miles on it. Used to be used by the forest service. Already done a bunch to it! Replaced the clutch kit, motor mounts, and got a new exhaust on it. Super happy with how she looks already. Paint isn’t...

BEFORE: AFTER: Gonna do the stock rims this week and see how it looks.

1990 Ranger XLT 4x4 2.9L Manual 5 speed Hello my fight post here and I am looking for some help. I recently bought a 90 ranger from BAT and about 1000 miles in the transmission seized up on the freeway and shredded itself. Seemed to stem from leaking fluid and maybe I was just sold a bunk...

Hello! New member of TRS here! Figured it was high time I made myself an introduction here and tell a bit about my history with the Ranger. My history with the Ranger goes back just two years when I got my first one at age 16. It was a 2000 Supercab XLT 3.0 Auto. I lovingly nicknamed this...

Hey all, Recently got this XLT with a ruined wiring harness for a good deal. 1 owner vehicle in AZ so no rust other than surface. Currently in progress for carb swapping the 2.3. Parts list so far: Weber 32/36 Racer Walsh adapter Speedway motors distributor Gm hei module Pc-91 e coil Fuel...

Hey all, Recently got my hands on a 2.3 that’s currently fuel injected but the engine wiring harness is toasted. Edward scissor hands got into the engine bay and went to town. Currently piecing together the conversion for carb based off posts here and other places. Here’s what I have so far...

Put a new slave cylinder in, bled the system with a handheld pressure pump and tried it the way the service manual said. Clutch pedal has more pressure than it did but not as much as it probably should. When my friend presses the pedal, the cylinder does not move. It just looks like this no...

I'll list, in order, the symptoms I noticed, and the steps I've taken thus far in attempting to fix the problem. Attempted to start my truck in the morning. I turn the key and I get nothing, not a sound. The starter does not try to roll over or anything. I check the radio and it works for now...

I need the front driver side window for 1990 ranger xlt. I was told one out of a bronco would work too. Anything from between at least 1988 to 1992 would work. I'm located in SC and I can't travel out of state so if it could be shipped or somebody meet me locally that would be great. Money is...

Can somebody tell me what this is. I took out my glove box and seen that this was corroded and I have no idea what this is. Do I need to replace this or could I just clean it up with a wire brush?

Hey there, I have a 1990 Bronco II XLT 4x4 that has been edging ever closer to finish. I've recently replaced the brakes almost in their entirety for the rear and still after bleeding the entire system have both the yellow and red brake lights illuminated and I now have a flashout CODE 4...

So I've officially finished rebuilding my passenger drum after replacing the siezed parking brake cable and so I began to bleed the brakes. I bled the passenger wheel cylinder first and was able to get brake fluid to bleed through it. Upon cracking the bleed valve on the driver side wheel...

So I've had an abs light and parking brake light on my dash since I got the old gal but she braked fine with fronts until now and ran unimpeded. Well I decided before taking her in for a smog since I just replaced the cat after a fail that I was going to safen her up and try to get at least one...

Hey there all! I just got back from a failed smog test. As you can see I got a pass on everything except my HC ppm at 15 mph and my NO ppm at both 15 and 25 mph. It has a fresh new o2 sensor and last i checked i had no codes. And they passed me on the OBD system check. I have not replaced the...

Hey there. 1990 Bii project trying to get to body restore but I'm having 4x4 and apparently transfer case end issue. If you check the attached photo, it appears that I have a leak at what I assume is the rubber piece and it's spraying my undercarriage something fierce. Any idea what the part is...

Hello! I swapped out my 4x4 transfer case motor on my 1990 Bronco II XLT and I now have no lights at the dash at all and zero control module actuation. Before the swap the lights would come on for both 4 Hi and 4 Lo and the you could hear the 4x4 control module function. Now there is zero...

Saturday, this 1.5 owner California-rust-free, 159k, 2002 XLT Supercab with smooth-running 2.3l 5spd beaut made a 350-mile drive home… interesting. ABS light came on when accelerating to pass The temp gauge decided to just languish at the bottom. 😬 After the third top-off of the tank, the...