swap

I have a 2001 ranger with a 2.5l, and i am wanting to swap the 5.0 exploer moter in it. i have heard that it is a direct swap plus the harness of course. i need to know how true the information is and guidance into the direction i need to go with this swap as far as if i can direct swap the...

I have a 1998 3.0 V6, and I swapped the automatic transmission out for a Mazda MR1 manual transmission last winter.:icon_welder: I had all of the important stuff hooked up, and I just left the backup lights for another day. I decided that I would like to get them hooked up this week hopefully...

First off i am new to this sight and the search option will not work for me. So im buying a 1995 ranger with a 2.3L engine and a 5 speed. I have a 1987 thunderbird that i took the motor and i want to rebuild it before i swap it into my ranger. Now when i do the swap i dont have alot of time to...

I have a '94 Ranger XLT ext cab with a 2.3L manual 5-speed that I am wanting to convert to a 302 w/AOD. Any suggestions, hints, tips, etc... would be greatly appreciated! :icon_hornsup:

I'm starting to get all my parts together to do a 289 v8 swap in my 1988 extended cab 4x4 ranger. My 289 has an fmx tranny on it right now and I'm wondering if I can run that when I do the v8 swap? If not, what type of t-case can I run behind a c4 to where I don't have to buy a $500 kit to run a...

well im just starting on the 5.0 swap and it doesnt seem too bad but does anybody have any advice. ive read the two tech articles over and over and im pretty excited. unfortunatly i dont have the complete explorer. but the junk yard does well any advice would be appreciated, thanks!

so my 2.3 is running shitty:pissedoff:and i wanna do a little of this:3gears:, so what should i go with to be the most simple bolt/plug&play way to go? 4.0sohc or ohv?

hopefully some of you can tell me what went wrong...i have a 2000 4wd that the springs were flat...so after reading a bunch i thought explorer leafs would be the best option...i went to my local u-pick and found a set off a 98 4 door with 80000 miles looked like they were in great...

im swapping a 84 5.0 carb motor into an 89 ranger and im trying to retain the stock fuel sytem. I need to know what the wires are coming out of the top of the sending unit and how to wire them to a relay? Can i use the stock lines and then run 1/4" lines to the regulator at the quick...

I currently drive a 1999 xlt 4.0 with 210000 miles on it... It is definitely a wonderful truck, but the front end has seen better days. My buddies dad just wrecked his 2003 xlt 4.0 that only had 120000 miles on it. I am looking at having the chance to get any parts off of his truck that I could...

hello everyone I was wondering, if it was possible to swap out my steering wheel (2004, w/cruise control buttons) with a steering wheel from a 2007-2010 Ford Ranger? I looked at the steering wheel on the 2007's and they look identical. Does anyone know if the connectors are the same on the...

I have a 1988 Ranger with a 2.9l and a 6inch skyjacer lift with 33's. I just bought a 1965 ford 289. My question is what all do I need to do the swap besides (engine mounts,headers,oil filter relocator,and an oil pan) What type of tranny should I use? Can I use the stock t-case? Any info will help.

tail light swap 99 Ranger? I have a 99' Ranger XLT 4x4, it currently has the red/yellow tail lights. I have seen some FX4 and Edges of the same generation i believe with a red/clear tail light (not aftermarket) does anyone know what/if any years of these are compatible with my 99'? I am...

i order a 1993 240 sx slave cylinder for my t5 swap does anyone know if my stock ranger master cylinder will work with it please help me!:icon_confused:

hi i need help finding lower radiator hoses for a 5.0 swap on an 89 ranger i have the ford explorer HD radiator please help thanks!:dunno:

My driver seat bracket is rusted out to were its not even connected to the floor.(sucks around turns and rocks back.) Its my understanding that Gen1 Exporer swap right. Is this coorect. I want to just get them from the junkyards and directly swap them in without modification if possible.

I have recently came across a 2003 Ranger 4L 2wd 5 speed with a rebuilt engine, transmission and new clutch (the problem is it got rear ended and the frame is screwed) and a 1998 Mazda B4000 4x4 5 speed with a perfect body but a blown engine and 400,000k on the transmission. I was wondering if...

Donor vehicle: 92 Ford Exploder, 4.0, Automatic everything, Push Button 4x4 The Patient: 85 Ford Bronco II, 2.8L carbed, 4spd w/OD, manual everything. Am I going to buy a new clutch? And if my understanding is correct, I have the M50D-R1 transmission, right? So it should bolt right up eh...

Hello! I really need help! I changed my old 4R55E wich broke a band to a 5R55E from a 1997 Explorer. The tranny was just rebuild. Lockup failed to engage immediatly when I took the car for a test drive. What happens is that when I pass a certain speed (80km/h) lockup should engage but instead...

I have an 88 Ford ranger 2.9 L super cab 4x4. The truck has been lifted excessively and is in desperate need of the one piece drive shaft swap. Locally I have not been able to source one. I found one in a salvage yard in Phoenix (about 150 miles away) out of a 2003 ranger, 4x4, extended cab...