engine

Hey guys. I've rebuilt my 88 ranger 2.9 l from top to bottom. My engine is running rich. I've replaced the idle air control valve, the o2, sensor, the pressure regulator twice, New injectors, New coolant sensor, map sensor twice, the computer and I've also shot all the wires. I did fuel pressure...

I own a 1990 Ranger XLT with a 2.9l V6 and the distributor is in a bad spot and is under the intake manifold and close to the firewall, and I don’t know if it’s possible to replace the distributor without dropping the engine.

What are these and where do they go? I was replacing my fuel injectors and when I pulled out the fuel rail, these fell into the engine bay. I didn't see where they fell from. And I can’t figure out where they go. Any help is appreciated! 2002 Ranger with the 2.3 Duratec motor for context. They...

Hi everybody Can I anyone help me? Where can I place the jack to lift my 2000 2.5 engine for replace the oil pan gasket, its leaking a lot of oil because a mechanic put silicone instead of the gasket years ago Thanks

Howdy there, I am trying to figure out the bolt sizes for my Ranger. It's a 1997 4.0 Manual transmission. The M50D-R1. I'd like to replace the bolts while I got the trans out.

Hello I have a problem with my Mazda B2500 00 Drive Side Engine Mount, I couldn't find it. It has a weird shape But the passenger side is like the standard ones. Could any one help me? _____________________ Spanish Hola Tengo un problema con el soporte de motor de mi Mazda b2500 del lado...

Hey all! Long time lurker, first time poster. (Yes, I’ll do an intro later.) Background: I have a 2003 Ford Ranger Edge 4x4 with the 4.0L SOHC. It has the very beginnings of the dreaded timing chain rattle, and i am trying to preserve the engine/timing for a bit more until I am able to do the...

I have gotten a 2001 Mazda B3000 3.0 automatic trans, (320,000 miles) 2wd, I’m looking to get a ball park figure and getting both transmission and engine rebuilt. They are both leaking transmission fluid and engine oil really bad from all different places so in order to fix the leaks it would...

I have a 1994 2.3 ranger with a 5 speed. I bought it not to long ago and it's run a little rough at times. So went to replace the icm thinking that was the problem. Unfortunately it is the harness someone used a bunch of house ground wire to repair it and now it's my problem. I really l I e...

Hi everyone, i'm from germany and in january i bought a 1986 ranger (which is an import car), unfortunately it broke down couple weeks after i bought it, the reason was a broken crankshaft. So i took it to a U.S Car workshop in germany (which are btw extremly rare) and the guy told me he will...

Hey Guys, This may be a lot, but if someone could provide me some expertise that would be GREATLY appreciated I know there is a million threads for this out there. And I have pretty much read them all. Hopefully someone on here can be of some assistance. I have certainly done my homework, but...

Hi Everyone! So glad to find this site. Recently purchased a 1988 Ranger with 84k original miles on it. A problem which has gotten worse in the last few weeks is the idling. When I am driving and come to a stop, it just wont stay idling. But it drives fine. I ordered an MAP sensor...

Hello! It's my first time to the forum :) I need to replace the engine on my newly-acquired 1992 Ford Ranger: 2.3 L, 4 cylinder, 5-speed, floor shifter. When looking for replacement (used) engines, do I have to match all these specs (1992, 2.3 L, 4 cylinder, 5-speed, floor shifter) or can...

Hi, I have a 1996 4.0 xlt 5 speed 2wd, the rear end hit a massive bolder in an ice storm and I bent the frame, trying to find out how easy it would be or if it is possible to swap my engine which is undamaged into another truck, I have a few options on what truck I can buy for this, they are all...

Hi all, first off i apologize if these questions are answered in here already. Ive never used forms before, and there is a ton of info in here and on the site, good work. A little overwhelming at times. Anyways my questions. Background story first. I do not have a ranger but am looking...

So, I have a 2000 B2500 SX, and want to replace the vinyl seats with cloth seats. Any recommendations on seats. I saw a 11 ranger and I would love those seats, but wasn’t sure about how it would fit. Also, any recommendations on things to do to the engine to get a little extra boost in power...

Hello, Good Day.. I am newly registered to the forums although I have been browsing it for quite some time. Very grateful of the community here. I have a 1992 Ford Ranger, was my first vehicle I purchased and it came with a lift already.. I had never owned a truck like this before and I have...

I bought a factory refurbished engine for my 94 Ranger from a popular auto parts store and never ended up using it. Still in the shipping crate with plastic on it. Gaskets included. 500obo Central Iowa Area but will travel some distance or meet halfway.

First post here so hi everyone ??. I just picked up this 1989 bronco 2 ranger conversion.I decoded the vin and it originally came with the 2.9 v6.... but the engine in it is not the 2.9 so someone swapped the engine along with the conversion . Could anyone help me identify what engine I have in...

Well, what I thought was just a leaking head gasket ended up being a crack from one of the cooling ports outwards toward the exhaust manifold, and about an inch down the side of the block. Pretty upset about it but I guess my question is, can these be successfully welded? I’m not willing to pull...