1999 XLT 4L V6 4x4. Rear diff is jarring/causing bad vibrations coming up to freeway speeds. I'm planning to pull the cover off and inspect for damage. Weird thing is it only does it 50% of the time, doesn't impact steering, and no funny noises yet. I feel like there might be some debris in...
Does anyone know if there are any compatible steering knuckles I can use to replace my old ones. I have a 1990 Bronco II 4x4 with a Dana 35. My current steering knuckles are pretty rusty and I want swap them out
I recently put a 8.8” axle from an explorer into my 1998 ford ranger 4WD, it had 10 inch drums before, now it has the explorer rear disk brakes. got the explorer brake line to connect into the rangers line, all seemed well. Until I road tested it, the pedal is very soft until the last 25% or so...
hey all, long time no see! did a complete front end refresh on the ranger (minus pivot bushings) and had a frustrating issue.
truck is a '90 manual hub d35 ttb
on the passenger side, the keyed hub washer with alignment holes for the inner nut was able to spin when torquing the outer nut.. the...
1993 XL 3.0 OHV
Leaf spring broke and connectors are in rough condition. O'Reilly has nearly everything except the axle u bolt top plate. Anyone know where I can pick one up?
Im selling an axle 4.10 / 7.5
its clean, pinon gear and spider gears are all in great condition. I dont need it after I bought it . I have brand new U bolts for it made at a shop for 75 lbs foot torque. I live in North Phoenix , Az.
Check out this item on OfferUp.
https://offerup.co/k2RItOrHTDb
Title about says it all. Swapping a 28 spline 8.8 axle from a 2000 ranger onto my 91 ranger, in the process of regearing with used 3,55 gears. Using the old pinion bearing as a setup bearing, dremeled it out to a slip fit, and am installing the pinion with the old crush sleeve, outer bearing...
1992 sclb
Located Lexington, SC
Seats -sold
Door panels with power window cutouts- sold
Trim - sold
Seat belts - $20 each
4wd module for push button 4.0 auto, untested. $15
Ttb d35 axle, 3.27 gear. $100 or trade for 2wd beams 1989+
Transfer case still in car, $150
Auto trans, still in car -...
I recently rebuilt the front suspension of my 2002 Mazda B4000/Ranger. I installed rebuilt Cardone CV axles
but even with new seals on the Dana 35 SLA they are leaking -- I suspect maybe ground down sealing surface too
much or bad splines?? The OEM Ford or Mazda Axles are NLA and everthing else...
i have 5/16 spacers on the front axle of my 1990 ranger and it has somewhat of a bulldog stance, will putting 5/16 spacers on the rear axle make it to where the stance is evened out or do i need larger/smaller spacers on the rear (kind of seems like i do) it has a DANA 35 TTB front and a 7.5...
So... I took my truck on a shortish (300 mile) trip yesterday, about 40 miles from home I was doing maybe 60mph on a long straight road when all of a sudden I felt a hideous death wobble and lost my front brakes (scared me pretty good). I carefully limped about a mile to a parking lot where I...
Been reading on how to do this swap on my Ranger and I think understand everything I need to do, but have one question before I buy donor axle from a junk yard. If I am planning on installing a locker, should I be looking for an open differential, LSD, or does it matter? Im thinking I want to...
I'm looking for parts to rebuild my 4x4 axle shaft. I recently bought a 94 Ranger, 4.0L V6 - I have a few questions:
anyone know where I can find parts for a Dana 35 front passenger axle shaft
anyone know what years of other Fords (Explorers/Broncos) use a Dana 35
I'm in Canada; I'm 17, I'll...
There are a few charts out there showing the RPM’s that you run with certain axle gears with certain tires at a given speed. I used one of these such charts from one of the posts I stumbled across on this website a long while back. Sorry, I don’t remember where I found it on here. I got tired...
Looking to lower the Green Meanie. Have the shackles flipped on the rear for now to level things up. Want to eventually do a drop beam/drop spring combo with an axle flip/frame notch. Won't have much of a budget so used parts is an option.
Does anyone know whether an R8 axle code from a 2008 Ranger is for sure 31-spline? There is one for sale on ebay but I don't want to pay for shipping if it's a regular 28-spline 8.8".
Thanks everyone!
Hey guys,
Does anyone know whether the 10" drum brakes from the old (2002) 7.5" axle can be reused on an 8.8 31-spline axle out of an FX4 Level-II? My drum brakes are in good shape and if I didn't have to bleed the brakes it seems like the job would be significantly easier... I heard the 8.8"...
Hey im going to be putting a Dana 44 from a jeep grand cherokee into my 97 ranger. This will be my first time doing an axle swap so im looking for some answers. The jeep axle comes with coil spring perches so im going to have to take those out and weld some leaf spring perches on there. thats no...
I hope this is the correct category for this post. If not, my apologies. I have a 2001 4x4 with 4.10 gears. I'm installing a fiberglass kit to widen the front and rear fenders by 4". It also has larger wheel openings that will allow me to install 35" tires with stock suspension. I'm also...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.