Search results

Hey guys. Thought id make a thread for my light install To start off im a volunteer firefighter and ambulance driver( hopefully soon to be lieutenant and emt) and my current light setup is not only ghetto but infective. I currintly run a federal signal slim something or other that was once...

Hey guys. Havent been on here in quite some time. But im finally back in a ranger so heres my issue, i just finnished up my front spring hangers, shock brackets,and new shocks (thanks jim for the best price around and ridiculous fast shipping ) and i also put a set of explorer springs in...

hi all, took some pics of my snowday toys past present and future(quad in the trailor,tj,and my 85) post em up and see what everyone's got sorry it isnt all rbv's but its all iv got for now and one hell of a fun time in the snow tell me that spare cover isnt BA!!:headbang: and what i...

thinking of buying an 88 2500 power ram its a 4 speed 4x4, id assume its a 318? it says v8 on the for sale thing thats all i really know, gonna look at it tomorrow night they only want $750 and it runs so, good buy, bad buy, any common problems it will be a dd for a while, and my tow rig for...

88 ranger, 4x4,5 speed, doesnt seem to have voltage to fuel pump new pump, fuse is ok, any ideas, i gotta check the grounds, past that im lost, mabe a chaffed wire? any common problems

hey yall, just bolted up a flowmaster super 40 or 44(i dont know or care for the price:D) and its just so damn loud, its a 3" inlet/outlet and a 2" reducer for the inlet, should i reduce the outlet, i want to quiet it down allot too, mabe some type of mesch screen mabe what should i do, 3"...

look for the ABS tone wheels on the stub shafts, those are the cream of the crop if the axel i pulled in school wasnt raped and pillaged, it would be in my truck already just cuz of the shafts

hey guys iv had my 85 since i was 13, thats 4 years and it needed major rust repair and valve stem seals, so my father decides to do a full rebuild, its been a work in progress for 2 years now and i just want it done What iv done: full brake system exept for 2 lines pads rotors calipers drums...

i hae a huge problem, i am in the middle of rebuilding a 2.8 and have found that the fromt bolt into the crankshaft is missing, does anybody have the specs on this bolt or have one they would sell me? i really need to get this truch done also if anyone has any suggestions on how to remove...

can someone please talk me off the ledge here i tryed to start playing multiplayer for the first time, and went on the wikipedia site and it says to open the confugureator but it doesnt say ANYWHERE on either site how to open it thanks in advance, this is drivin me crazy

hey guys, i just finnished up my 81 yamaha fix up with a new battery today and i cant get the bike to actually run, itl turn over and backfire now and then but it wont run for more than a sec. i pulled and cleaned all 4 plugs(4 cylinder) and tomorrow in going to drain all the gas out of it...

i bought a new shift knob, but the hole is the wrong size(meant to be a jockey shift for a motorcycle) does anybody have any idea on the size i should drill it to and what else i should to to secure it(it has set screw holes,but no screws) also, is the leaver on an 854x4,(2.8), and an...

not to jack the thread here , but is the d44ttb a bolt in axel? i have one i could have if i asked nice enough

these are from last summer(about july 10th) meet the blue bomber me driving it(my friends truck) and the worst part of the day, and just rember kiddys, dont use the words "no balls" when you dont have a big enough truck to fix your mistake he wasnt happy out tools; one jeep wrangler(4.0...

it explains itself

i would do a d44 ttb front and 9 inch(with some work) if i were you, i like ttb and 9 inches tho

ok iv been promicing pics of my 88, and i finally had the time to take a few ,so here they are the light bar off the other truck and some cheepo lights, and my dice:icon_bounceblue: my exaust,notice the placement:icon_hornsup::thefinger: and the sticker on the gas door, idk y i took a...

hey guys i just picked up another ranger its an 88,4x4 4 speed standard cab longbed with a 2.9, and it runs ok, but i just have a couple ?s it doesnt have any pober lowend, and tends to buck a lil bit?, its getting a fuel filter and possibly the in tank pump the temp and gas gaidge dont...

hey i was thinling about doing a duraspark swap as soon as i get my truck ready to reassemble it so i wanted to make sure of a few things what carbs can i use with the setup, i have a bunch of old ford 2bbl v8 carbs i can have, not sure wich ones will work will it still pass emmisions? i live...

its not really hard to do, just make sure you put the hub back in (little peices) in the correct order/torque, and you should be fine, its really not a hard job to do, its really good to know tho, o and ball joint tools are great for doin u joints too, so id buy a press if you think youll hav to...