wiring diagram

I am in the midst of swapping my 4.0 into my 85 bronco 2. Before pulling the engine, i had all lights and signals. After pulling the engine and engine harness there is no power to anything. Lights should be on an independent circuit, but nothing is working. Excuse my crude drawling but this is...

I have a 1996 Truck with factory AC, so I will use this thread to take some notes on how I get the system operational again and ask for advice The first step has been to inspect the various components of the system to see what works and what does not. I will divide this into a few section AC...

Hey All, I finally got my 2000 Ranger 4.0 OHV fixed. I broke down and took it to the shop.. Turned out to be a clogged catalytic converter. The Mechanic tried his scanner (on top of my Launch, Innova, and Actron) but couldn't get communication from the ECU (is what the scanner says). It won't...

Greetings! Let me start by saying I'm sorry if this isn't the right place to post, I'm not really sure where my issue/struggle fits in. Please give me a chance to move the text to the appropriate thread before I get deleted. I joined because every other search I've done while working on my...

So I went out and dug out my truck today and went to wash the windshield and my wipers stopped in the up position and wont move on there own now. My pissers still work and if my understanding is correct they are on the same circuit so no blown fuse... I think? I'm thinking a bad wiper motor but...

Can anyone tell me which of the 2 VSS wires is the Positive Signal Wire on a 94 Ranger 3.0L? The drawing I have has a Gry/Blk wire from the PCM (pin 3) and a Pnk/Org wire (Pin 6). It looks like the Pnk/Org wire is connected to a ground ( the drawing has a dot in the middle of the line, but all...

Thank you for any help I receive before hand. I have a bad harness on my 99. I have looked around, but my harness is discontinued, and i hate to rebuild the one I have. I found one for a 98 that looks the same from what Ican tell. Both are for 2.5l manuals. My 1999 part number is...

I have ran into a problem that the previous owner of my truck failed to mention. He torched some wires on the harness section that goes to the fuel inectors o2 sensor and possibly the tranny. I got a harness from the junk yard for my truck off a 97 Ranger 4.0l the only difference between it and...

Trying to fix my son's 2003 2.3L manual Ranger. Shows following codes: P2004 Manifold Runner Control stuck open P2008 Intake Manifold Runner Control circuit open P0403 EGR System fault (fault in EGR solenoid circuit) P0446 Evap emission system purge/ven solenoid circuit open P0597 Thermostat...

at the junk yard i found an explorer(93) with the premium sound, i pulled the whole rear setup (amps + sub) my question is 1. which amp does the speakers, theres a silver one and a black one 2 what is the pin out for above amp (left, right, power) i think the amp for the sub is straight...

Since my BII is down and it is too cold to work on it outside, i decided to yank the electrical system out of it & create wiring diagrams for all the harnesses and during this process fix the wiring issues im experiencing. The first one i have completed is the Main Cab Harness (including the...

I need a wiring diagram for adding daytime running lights to my 91 Ranger. It doesnt have any now and I'd like to have them on only when Key On. There are small bulbs in the new headlight bulbs I just installed with 2 wires for the running lights left hanging there, headlights work great but I...

I have a 2000 ranger 4 cylinder with no pats system, I just installed a 99 4.0 explorer engine which has pats. The last thing I need to figure out before I can start it is how to install pats. I have the complete doner, do I need to switch the complete steering column, or can I just install the...

I just bought this truck for work, so I honestly don't know much about it. When I went to look at it before I bought it, the AC worked fine. I had to put a radiator in it, then drove it home. After I got home, the AC stopped working. Light on the control panel comes on, but nothing beyond that...

When I bought the truck, the selector switch on the dash was set to the aux rear tank, the fuel gauge worked and so I just used the rear tank. I've left it alone for all these years. My son filled the rear tank with Biodiesel and then a norther blew in so I thought I'd be smart and put some...