I found a bed on marketplace that was noy too far away. It looked like it was in pretty good shape, but the guy had a buyer that was going to pick it up last Thursday and I couldn't make arrangements to get it that soon. On Tuesday I got a picture from my son of what looked like the bed in the...
Superj, will you deliver if I get one of those from Texas? I live in the north end of Illinois :)
Lefty, yours looks good especially for Minnesota. That's the drawback with these steel beds covered with fiberglass, they look good on the outside and rusting away underneath. I was just looking...
My sons took my bed off yesterday and I got the filler hose replaced. That was actually the easy part. My bed bolts were rusted and most of them broke. With the bed off I could see that the bed is mostly rust, the front passenger side was held together by the spray in bed liner, the bolt in that...
One of you guys that are going to do all that work to your truck bed, have a flare side bed without the fiberglass sides you want to get rid of? I was going to pull my bed off to replace the rubber fuel line that goes from the fender to the tank, and I noticed my bed is really rusty. Most...
Success, I replaced the ignition switch and that seems to have fixed the issue. Thanks to franklin2 for telling me twice to replace the ignition switch. Am I the only one that thought most vehicles had the power going through the ignition switch with the key in it that is now on the steering column?
I'm not sure which switch is the electrical switch. The one under the dash has a plug on it but I inspected it yesterday and I can't see any obvious problems. I replaced it once, but I don't remember what the problem was then. Do those wear out easy because it's only been a couple of years? My...
Lefty, I got both the small led light bar and the switch box from SpeedTech Lights. They sell a bunch of emergency vehicle lights. They sell the off-road lights too.
I can't find the name of the company I got it from. I'll look some more and put it on here when I find it. I came with the 3 switches but one was spring loaded so you could push it and your light would come on only when the switch was pushed, I had them send me another regular on/off switch, the...
I got this switch online from a company that deals in lights for emergency vehicles. I figured it would be more dependable form them than one on Amazon. It looks a lot like the one I saw in a previous post. I bolted it to the housing the passenger side air bag switch is located but it is just...
My 04 Ranger with a 4.0 stalled when I was taking off from a red light. When I tried to start it, didn't do anything. I tried a few times and on the last try I let the key turn back from the start position just a little and it started. Anyone have an idea what causes this problem? It did it once...
Wow, I got a lot of input on this one. It's a remanufactured motor so I'm not going to take up to any of the maximum RPM. It is nice to know the highest RPM that is recommended, I have a couple of motorcycles and one of them I use to run it up to maximum RPM regularly. I'm older now but I'm...
I have a 2004 Ranger FX4, it has a manual trans. Can someone tell me why they didn't put a red line on the tach? The exhaust is so quiet I can't hear the motor good enough sometimes to tell when it's time to shift. It's not a real problem, just curious if anyone knows the reason. A guy I work...
When I did my first inspection checked the u-joints by spinning the drive shaft and trying to move the u-joints and didn't notice any unusual movement. Yesterday I changed the fluid in the rear end, I turned the whole drive train using the ring gear to inspect the gears in the rear end, didn't...
I checked the universal joints, and they didn't appear to have any movement. I have a 1-piece drive shaft. I'm going out to change the lube in the rear end in a few minutes. If it looks OK, as in normal wear I'll take a closer look at the universal joints. I haven't noticed any vibration in the...
Well, the last 2 days I didn't notice the vibration, maybe I lucked out and it was just the old Cooper Discovery tires. They were on the truck when I bought it and they were in pretty good shape. The first year the seemed OK but after that they are not any good it the snow. I just checked the...
Sorry, I didn't specify, it's a stick shift. My thought is either u-joints or rear end. Maybe bearings in the rear end. What confuses me is it just started. I have a 7 mile commute each way, mostly in town. I think it happens around 50 too. It's hard to tell because I only get up to that speed...
I have a 04 FX4 and it just started vibrating in 2nd gear. I jacked it up and checked for loose wheels and extra play in drive shaft and rear end. There is a little slop in the drive train. I've only had the truck for a few years, and it seemed like it was pretty well maintained except for the...
Thanks guys, I thought that's what I needed. That NAPA number I put in my last post is supposed to be the 2721 with the 1/4 turn holder on it. I read that the 2721 from dealer has the those holders glued on to the bulbs.
Plum Ranger, what bulb did you use to replace the bulbs in your Ranger? I thought mine had 194 but I did some research and mine is supposed to have 2721, another option is a74 . I work part-time at a NAPA and one of the counter guys looked them up and NAPA has a bulb that come with the 1/4...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.