Recent content by fyre82

Thank you Ron

'88 2.9 I'm looking for information on which relay is which in the right rear of the engine compartment. There are 3 fuel, ecm and one other. 2 are this type relay. One is light color and one dark, @RonD Thanks Rich

My 2000 1/2 has Live Axles. Ford changed the front end mid model year 2000. I wanted hubs . . .

You are correct Senornoob, the torsion bars are removed, those are coil over Bilstien. I stumble with jargon... What is it you feel you are missing? I'll do the best I can. I'll research with superlift and RCD. Thanks

Hey guys, I need some help to identify what brand lift is on my 2K Ranger 4x. Best as I can tell it is 6" lift, anyone recognize the style of the lift box? I can't find a mark on any of the parts other than the part number on the knuckle. I am in need of a left lift knuckle as it got a bit...

I've been struggling with a similar intermittent no fuel problem in my 88, most recently twice with higher temp, 210 and AC on. It died like it was out of fuel, pump ran at key on and gave me spurts of fuel and air at the schrader. It wouldn't start until it cooled below 190, after the flatbed...

My '88 ranger 2.9, manual, has been suffering with a cranking issue. I turn the key, the lights go out like they do when it starts, the starter does nothing. If I leave the key on in neutral I can jump the solenoid and it fires right off. This started last spring, I suffered with it for awhile...

My 2000 4.0 4x automatic, developed an issue a few days ago that has continued to perplex me. I was driving home when the 'check gauge' light comes on. Temp gauge is high, not HOT. It goes down, light goes out, a couple of repeats of this I stop, check, and it definitely isn't HOT, coolant is...

2000 Ranger 4.0 4x4 I have an intermittent check engine light for a slow O2 sensor, known malfunction. If it bothers me I turn it off with my Inova code reader. Got the light again, went to connect the reader and it won't connect to the computer, hot, cold, key on/off, engine on/off. Tried it...

I recently put some 1.5' coil spacers in my previously lifted 88 supercab to try to get it aligned in front. That went well, all I need to do now is adjust the bushings some to bring the wheels up straight. What I have now is the rear is significantly lower. It was before but now it's really...

2K Ranger XLT 4.0 4x supercab steppy, I have some intermittent electrical issues that I have been working through. I can't find a good inside fuse panel scheme for this rig. I found some in interwebz search but haven't been successful in specific diagrams. My rig just happens to have a 06/00...

I posted this in General, decent looks, no feedback . . . I did search through this thread and didn't find what I was looking for. What I need is where to find some longer, braided, front brake lines for my lifted '00 Ranger. Or what application works. Thanks Rich

I recently acquired a nicely lifted '00 supercab. I didn't like the heavy offset wheels that were on it and swapped them out for some soft 8's. Long story short, the right front brake line rubbed on the inside wheel weight and consequently failed. I was stopped fortunately. The truck had braided...

I'm working on an '03 3.0 Ranger. It won't rev above 3K rpm, at that point it acts like it's running on less than 6 cylinders. There are no codes, none stored. I replaced air filter, fuel filter and plugs with no improvement. The truck ran fine until it was stolen, now it has this issue. Any...

I have had it out once in that capacity, mostly used it as the chuckwagon as we always preferred to sleep out under the stars. This one as built is not as good as a sleeper due to many of the reasons Alan mentioned above. If I put an adjustable 'foot' on the rear corners that would help...