Today I realized that my wheel bearing/hub assembly on the drivers side tire is completely shot, in addition to my tie rod ends...and I'm sure my 33" MTs are to blame...so I was wondering if anyone could advise on good performance aftermarket replacements that can handle these big tires? Thanks...
I'm having this issue with my 1999 Ranger XLT with the 3.0 -- When I am going up a hill at 3000RPM or higher, the vents will start blowing through the defrost. Its very annoying! Does anyone have any ideas about this? I assume its some sort of vacuum issue...I also know that this model had...
Okay, here's the situation. I knew the starter or something was about to go after i'd start my truck and here a slight squeal (off the flywheel?) after starting. But now, my truck is sitting in the driveway, and to get the starter to do anything I have to jump it. The battery is BRAND NEW, and...
What do you guys think of say 4x4 hi on wet roads? As some of you Pennsylvanians might now it has been pretty pissy/rainy outside and i am tired of spinning out on every damn corner. Ive been pondering this but not sure if it would be good for the drivetrain or what not. What do you guys think?
So I tagged along with some guys in the area to a local offroad trail called trails road...thought i'd share some photography!
Some 3 wheelin'
TK's purple rig
Not bad for stock suspension :icon_thumby:
look how purple tk's ranger is ha ha
So I just got my rear axle seals replaced and wheel cylinders and shoes, all on the rear, but when I got it back yesterday, I noticed that when I make a hard right turn, what seems to be the passenger front wheel shakes violently and it feels like the wheel is gonna fly off. This also happens...
So when I put my rear bumper back on after my lift, I decided to remove the connector for where you'd plug a trailer brake light thing into. So, like an idiot I just tin snipped the wires off because I didn't have the stupid tiny torque fitting that required, and it was too corroded anyway. So...
Well I finally got my body lift done and Monday I went to pick up my new Procomp MTs (33x12.50) on Mickey Thompson Classics. I think she turned out pretty good!
<He he, IFS loves flex! :icon_bounceblue:
Coming soon - painting frame, new axle seal and rear brake :annoyed:, some homemade...
To all with the 3" body lift on newer rangers, and perhaps those on older ones as well. I know someone here has made homemade gap guards, and I'm curious as to what material you used and the best way to attach it up in the fenders. My dad seems to think that rubber would rot and maybe a flexible...
Hi guys, I couldn't find anything about the proper wheel width for this size tire. I currently have the 3" PA body lift and need to get a new set of rims before i get my new tires...but I'm not sure what width to get? Would an 8" do? or would a 10" be better? Thanks for your input!
Hey guys, just as the title says I just completed my body lift today, and viola, go to drive, and my Pioneer stereo is dead. I checked all wires and fuses I possibly could, and everything looks fine. Also have a pair of aftermarket foglites and one of them quit working (pretty sure it isn't...
I was wondering of those who have done the 3" lift for a 4th gen how you went about installing the rear bumper brackets. Me and a buddy are trying to figure this one out and plus two of the bolts are insanely tight so we're hoping those bolts wont needed to be removed. If anyone could post a...
I think I've narrowed it down to one of these two. What are your opinions, which do you think is better? I'm about to get my new 33's next week :-) Want to make sure I get the right ones. Thanks! Also, which ones are generally cheaper? I can't find local online quotes for places near me, guess...
What do you guys think of this setup? I have yet to clean up my rear's inspection tag to see what gears I have although I'm quite sure theyre 3.73. Anyone run 33's on em? How much slower is this setup? or maybe I should go with 32x11.50s? any help is appreciated as my lift is being installed in...
Hi everyone, I plan on installing this lift within the next few weeks, and i'm wondering how this will affect my front tow hooks. Will I have to remove the part of the bumper underneath them altogether? I just think it will look weird but i dont really know...any help thanks
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.