Latest activity

What's new Featured content New posts New media New media comments Latest activity
  • Robertmangrum.rm
    Robertmangrum.rm reacted to Jim Oaks's post in the thread Stolen content on Facebook. with Like Like.
    At least he could have done was link to where the truck is posted...
  • Robertmangrum.rm
    Robertmangrum.rm reacted to superj's post in the thread 6th gen bed side step install with Like Like.
    If you dont have the steps behind the rear wheels and you happen to come across a good deal getting them, they are very easy to install...
  • 02FX4shadow replied to the thread M50D-R1HD.
    The hard part is i dont know which i have since all the stickers fell off over time and I cant identify which one I need.
  • GingeeShotz replied to the thread Really need help with Diag.
    Yeah I think I’ve been just lying to myself these past few months. Somewhere I read said it could be the TCC. I’m going to bring it to a...
  • 4x4junkie
    4x4junkie replied to the thread 1996 Ranger Difficult Shifting.
    Well there are a multitude of different ATF types out there nowadays... You can't just put any ol' ATF that happens to be the closest...
  • RobWigglezz
    RobWigglezz reacted to pjtoledo's post in the thread 1996 Ranger Difficult Shifting with Like Like.
    a bad pilot bearing can cause the input shaft to keep turning even when you have the clutch depressed. with the engine off, can you go...
  • pjtoledo
    pjtoledo replied to the thread 1996 Ranger Difficult Shifting.
    a bad pilot bearing can cause the input shaft to keep turning even when you have the clutch depressed. with the engine off, can you go...
  • RobWigglezz
    RobWigglezz replied to the thread Really need help with Diag.
    The lurching forward at a stop is interesting. The torque converter needs rpm to couple unless it's coming apart and trying to weld...
  • scotts90ranger
    scotts90ranger replied to the thread 2.5L ('98-'01) Oil Leak.
    If the oil leak is above the thermostat then the only real source is either the cam seal or the cam pulley bolt, both can be tackled...
  • pjtoledo
    pjtoledo replied to the thread About to start front suspension rebuild.
    check for wear on bottom side of the spindles where the bearing races are. take the dust cap off and check for movement when you do the...
  • RobWigglezz
    RobWigglezz replied to the thread 1996 Ranger Difficult Shifting.
    The squeal is probably metal on metal contact somewhere. I had a very sticky 1 - 2 shift that sometimes required a double clutch...
  • RobWigglezz
    RobWigglezz reacted to 4x4junkie's post in the thread 1996 Ranger Difficult Shifting with Like Like.
    This sounds like it could be a clutch issue or fluid issue... (at least all except the part about it squealing... that part sounds like...
  • Jay11 reacted to franklin2's post in the thread 2.5L ('98-'01) Oil Leak with Like Like.
    I just fell into a trap which may have caught you also. I looked up the timing cover seal, but found out they gave me the aux shaft...
  • Jay11 reacted to scotts90ranger's post in the thread 2.5L ('98-'01) Oil Leak with Like Like.
    Looks like a Timken 2955. It's probably that or the housing that it mounts in, unless it's the O ring for the oil pump that's behind...
  • Jay11 replied to the thread 2.5L ('98-'01) Oil Leak.
    Starting to tackle this. Got the Tstat housing out and here is a close up of the leak. Where is the source of the leak and what should I...
    • oil leak.jpg
Show older items

Sponsored Ad

Back
Top