• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

harness


  1. 4r44e Wiring Question

    TLDR: What does the 2 wire connector in the picture go to and how much will it suck to reconnect it?? I have a 150K+ miles 1996 Ford Ranger, Automatic and I've had issues with the transmission. I only paid $1000 for the whole truck so a rebuild kinda ruins my investment costs. I am trying to...
  2. 90 ranger solenoid to power distribution wire bad

    I'm helping a buddy out with his truck, he has been dealing with a random no start/die while driving issue for a month or two, well, the shop he took it to said the crank position sensor was bad, so we changed it, the same issue persisted. I was looking at the power box under the hood and...
  3. Dmgctrl88

    2.9 to 5.0 Wiring Harness Conversion

    So I've been on here quite a bit and I currently have a build thread going. I'm almost done building my motor and was looking ahead to my next task to overcome. So some basic details before going in about my build. 86' 2.9 A4LD 4x4 converting to an 5.0 & C4 retaining the original BW1350...
  4. Making 97 5.0 to 03 ranger jumper harness...need help

    Ive got an 03 ranger single cab that came with a 3.0 stick shift. I'm using an early 97 explorer pcm so I went to the junkyard and cut the 42 pin connector off of the body side of a 5.0 explorer and I cut the 42 pin engine harness side of the ranger. I want to make a jumper harness between the 2...
  5. dogboy

    Obd2 explorer v8 with Obd1 dash?

    I've searched a little, and can't find anything. Has anybody done a 5.0l v8 swap using a 96 Explorer engine harness, but retain the 94 Ranger dash? I'm kind of stuck on my swap, because this 96 Explorer dash and body harness isn't going into my 4.0l 94 Ranger like I thought it would.
  6. 84bluebronco2

    Head light switch issue

    94 Explorer XLT Head lights have been acting up recently, as in pull switch and lights occasionally decide to illuminate. If you fiddle with the switch you could get them to turn on... replaced switch today, no headlights at all... Tried original switch, brand new replacement, and a spare...
  7. Tail light dilemma

    So here's the deal, I've got an 01 edge so I have 2 bulb tail lights and I'm gonna be putting up a bar to replace them using trailer lights and I want to run separate brake a signal lights. I'm trying to essentially convert from the 2 bulb to 3 bulb setup and I've searched but found no answer...
  8. Camshaft Position Sensor 98' Ranger

    Hello everyone first time poster here. I am posting on the behalf of my uncle who has no knowledge of computers whatsoever, and needs help regarding the camshaft position sensor. He's got a 4WD 98' Ranger, 4.0L manual. Any help at all would be much appreciated! The following is all of the...
  9. 1988 Ford Bronco II Main Cab Harness Diagram

    Since my BII is down and it is too cold to work on it outside, i decided to yank the electrical system out of it & create wiring diagrams for all the harnesses and during this process fix the wiring issues im experiencing. The first one i have completed is the Main Cab Harness (including the...
  10. HID retrofit wiring? HELP

    I just finished retrofitting a set of h1 mini projectors into the stock housings of my 01 mazda. I cant figure out the wiring. The truck harness has a HB5 connector but the kit is H1 bulbs with a shutter in the projector. I am a noob at wiring and I cant figure out how I should wire everything...
  11. 4L Manual Trans Harness Mystery

    1997 Ford Explorer 4L SOHC So I did an Automatic Trans swap from 5R55E to the 5 peed M50D. all is well but the computer is not liking it! Here is what I did: On the Transmission wiring harness, from the two big connectors at the back of the engine, I cut out the DTR connector and used the...


Top