Search results

Trying to remove rotors on 94 ford ranger how do u remove the hub?

Was trying to figure out the speaker size in my truck and what other sizes would fit. At the store now

Hey just a couple quick questions. I have a 1994 ranger I was wondering if 2003 grill hood headlights and front fenders would bolt right up? And will the body lines match? Any info appreciated, thanks

So in my 2005 xlt F-150 5.4 v8 the engine at anything above 3500 RPMs the engine will act like its in neutral and wont give it any more power to the engine, also at around 1500 RPMs the truck sort of cuts out, the rpms dont drop or anything but it kinda feels like going down a really bumpy road...

engine is choking on my 4.0 ohv, will be driving and the rpm's will suddenly just drop by a few hundred rpms, feel as if i tap the brakes for a split second, it randomly does it, will keep doing it and if i dont keep revving the engine it will stall, i have so far cleaned the maf, replaced the...

hey just a quick question, i posted awhile ago about my truck running terribly and i think i found out that it is the fuel pump as sometimes while it is still running the tach will say it is at 0rpm's, obviously meaning it would be off so does the tachometer run off of the fuel pump?

so while driving down the road it randomly began, the rpms would drop by a few hundred for a split second, and it felt almost as if i was tapping the brakes, so i went home, by the time i got there ( 15 minute drive) the rpms were constantly dropping by around 500, i would have to keep it above...

so i have a D35 and it has auto locking hubs, i hate em, probably a stupid question but would manual hubs from a D28 work?

ok so im doing the heater core right now on a 1994 ranger 4.0, i drained radiator, disconnected heater hoses, and took the 4 scews out so im at the heater core right now but im looking up to it, theres not much space its sort of in a rectangular box, where would i go from here? are there hose...

so i have a 94 ranger with the m50d transmission and the 1354E transfercase i believe, its electric, i press the button and it will go into 4wd but wont go into 4lo, the fuse isnt blown or anything and from what ive checked everythings hooked up, what could this be?

so on my 1994 4.0 the oil pressure gauge doesnt work but i found a wire that isnt connected but cant figure out where it goes, connected beside the oil pressure sensor theres another wire that is probably a foot or a foot and a half long that i cant figure out where it goes, any ideas?

so i need to replace the exhaust flange gasket on my 94 ranger 4.0 MT, i have tried getting 2 of the nuts off the studs and they both broke, do i just tap the studs out? and the last stud that im not able to get is between the body the transmission and the exhaust, what would be the easiest way...

so my oil pressure gauge in the dash isnt working, the wire is connected, any ideas on what this could be? thanks

hey everyone, i was just wondering what transfer case is on the back of the manual transmission behind the 1988 2.9 v6, its a manual T case, would that be the 1354M? and if so would it bolt up to the back of a M50D manual transmission that came behind the 4.0 ohv? i currently have a Electric T...

so i posted a couple days back that when i try and start the truck the starter makes a horrible grinding sound because it doesnt disengage, well i tried to bump start it today and when i went to drop the clutch i heard the sound of the starter on the flyweel, what would cause this?

i just started my truck for the first time since i swapped a new 4.0 ohv engine into it, it has the m5od transmission, once started it made a constant horrible grinding noise, sounded like it was coming from the right side by where the engine connects to the transmission and sparks were coming...

i own a 1994 ford ranger 4.0 ohv with the m5od manual transmission, i was looking around the engine bay the other day and theres a plug right above where the bell housing connects to the back of the engine, i cant find the wire that connects to it anywhere, what would that plug be? and would...

i have a 4wd 1987 ford ranger 2.9 with the a4ld transmission, the transmission went out and im here looking at a new 1 i found on craigslist but it is a 2wd transmission, will it work on my truck and allow me to still bolt the transfer case up for 4wd?

hi everyone, i have a first gen 1987 ford ranger with the dana 28 up front and 8.8 in the rear, i was wondering how hard would it be to swap a dana 35 up front? thanks

so im currently looking at a 1993 Ford Explorer 4.0 ohv 5 spd manual on D44 and ford 9" with hydro steer, it needs new coils, steering bushings, and gears, if i were to use this as a weekend warrior/ daily driver what wld be the best gearing and coils to run? and how much wld steering bushings...