Search results

I've got a full width 44 from a 78 bronco to go under my ranger. I've been looking into all of the SAS build threads i can find. Seems like most guys are running a T linkage, and i think that is the way I want to go, for simplicity. I do not have a stock bronco tierod or draglink, which is fine...

Hi all I have a few questions on setting up an 8.8. - Does the pinion crush sleeve go beneath or on top of the outer pinion bearing and race? - What is the in.lb torque spec for pinion preload? Thanks

Around new years I dove into a cut and turn d35 project. I set my goals: 4" added spring height for 6" of lift, and strategic bracing to make the beams stronger. I want to run 35's when all is said and done. I did a bunch of research and looked at alot of set ups. I decided against relocating...

I have a 94 with a 4.0, and have what I believe is a vacuum issue associated with the brake booster. When driving, say approaching a stop, clutch in or in neutral, when I apply the brakes the idle stumbles and if not revved, the motor stalls. I've checked the hose from the manifold to the...

In reading around the forced induction forum, i'm seeing alot of mention and discussion about proper tuning. I've seen a few builds tuned, and recomended to tune with tuning software such as Sniper or SCT. I am wondering what the engine management/diagnostic system requirements are for these...

Hi all I just discovered the other night that with thw heels jacked up off the ground, by pulling and pushing on the wheel, I can move it inwards and outwards about 1/2 an inch :shok: What do you think is causing this? I can only imagine it may be worn c clips or a broken S spring in my trac...

Hi all I'm looking at purchasing the Moog K8986 alignment bushing kit. $27 on amazon seemes like a killer price. Does anybody know whether this includes bushings for both sides, or just one?

So being the frugal college student I am, I have been looking into steel fenders i could use as inners to enlarge my wheel wells to fit larger tires without lift. Poking around online i've found some good options in the $30-50 per fender price range. Tonight I went to home depot, and something...

I happened upon a set of D35 beams and arms for free. I've been reading whatever I can find about cutting and turning. I want to run 3" of lift, to match the coils I have. With some simple trig applied to the length of the beam, and the change in coil height, I have decided I need to build 6...

Hi guys Just wired a couple 6" offroad lights to my factory fog wiring. I don't like how I can only run the lights in low beam. When I hit the high beams, or if the headlights are off, I cant use them. Do you guys know a way of bypassing this keeping the stock switch?

So my buddy tows for a living, called me up last night "Hey there's a turbocharged ranger down at the tow lot!" I ran down there to check it out. The truck is a 90 std cab long bed it is a 2.3 turbo. Under the hood is what I guess to be a turbocoupe or mustang motor. It was equipped with an...

Hey, check out this ad. This guys selling a 5.0 with he claims to be an M5OD trans. did they put the M5Od behind the 5.0? Direct bolt in to a 4.0 truck with an M5OD? http://boston.craigslist.org/bmw/pts/1116157362.html

Hi all, lets set up a meet for Massachusetts! TRAIL RIDE INFO -May 2nd 2009 -Meet at 10am, leave for trail by 1030 -Meet at Brians place, it a gas station on rt# 140 N (Gardner Rd.) about 5 miles off rt#2 on the left in Ashburnham -Stock 4x4 capable. -Front and rear tow points preferred...

Gave the ranger new paint tonight. Inspired by Krylon's primer, color Ruddy Brown, and made possible by cheap colorplace cans of the same color, comes a 94 Extended cab short bed 4wheel ranger. The color is awesome. I've done something on the grill and hood too. I'll leave you with that , pics...

Hi all, I just got an nice e-fan for the whopping price of one marlboro red. I'm also looking to ditch my AC comprosser, as my condensor is long gone and all my lines are junk. Will I need to find a bracket to eliminate the AC, or can I just go with a non-AC belt? Will improvements in power...

Hi all, whats the best/cheapest way to ship a trans? would ups take it? build a crate for it, or pallet it?

pardon my title, but I really do have a stiffy on my hands. I'm running stock coils, 4 and and an overload leaf springs, and skyjacker shocks on my 94 extended cab shortbed. I don't have the ride quality i'm looking for. It seems like even mild bumps and deformities in the road are all very...

Hi guys, Wondering what shipping weight would be on the dana 35 pig, with gear and carrier installed, nothing else with it. (no shafts, arm, etc.) thanks Erik

Hi all, newer member, looking for help with my front end project. I bought front and rear axles, 3.73's, to replace my 3.07's. The rear pig was mint. The front I wasn't so lucky. All the bearings were rusty, all seals dry and cracked. I have all new parts for the front diff, minus the gears and...