Search results

I am looking for bolt on caliper steering knuckles or complete axle if you do not want to separate. Thanks Text 949 683 5604

My 1989 poly tank is leaking on the front side closest to the transfercase and needs to be replaced, no one makes a replacement tank past 1988 metal ones. 1. will the 1988 metal replacement tank work with the 1989 sending unit/pump and will the tank straps work as well? 2. Or will a newer...

In need of a Dana 35 Passenger beam housing in good shape no cracks. Thanks,

Can someone please provide a dimension for the driver beam pivot that is on the passenger frame rail from the frame to the pivot bolt for a STX pivot. I have searched and there are a lot of photos but none with dimensions. Thanks,

I have a Dana 28 TTB 3.73 gears hub to hub $125.00, Ford 7.5 LS3.73 $125.00, Supercab rear drive shaft 1210 series with newer u-joint and carrier bearing $100.00, axles and drive shaft have 170,000 miles. Skyjacker 134 rear leaf springs $125, New Dana 35 TTB Lock-Right 2310-LR with correct...

I am switching to a dana 35 and epo 8.8 and I need to change the driveshafts to the series 1310 . What is the spline count and diameter for the front and rear output shafts of the BW 1354 and are the 1350 the same? Thanks

The tech write-up for the dana 28/35 does not address the issue that the driveshaft and transfer case yoke have to change from the 1210 series to the 1310 series universal joints- what is the easiest way to resolve the front and does anyone make a 1210 pinion flange for the 8.8? Thanks

I picked up a set of 1994 Explorer full power bucket seat to install in my 1989 ranger supercab. The explorer seat brackets do not line up with the ranger floor pan, has any one completed this swap and have pictures showing how they were mounted? I have search and have not found any thing that...

Will a 1990 2.9 v6 auto trans harness work in a 1989 manual trans truck? Thanks

Can an automatic trans harness work on a manual trans/ maunual computer?

where is the chime relay located, I can hear mine any more. Thank you,

Is there any difference between the reay you would ge from an autoparts store and a Ford dealer? Are they all made by manufactures other than Ford? What brands are recommended? Are there any aoto parts stores that can test them? Thanks

1989 2.9 , I have spark but the fuel pump does not pump, I have no power at the 30 amp fuse that powers the relay. Does the power come from the ECC or is it direct from the battery. What should I look for or test. Thank you

I have a 1989 Ranger 4x4 STX Supercab with a 2.9 V6. I have 12.23 V at the battery terminals by testing with multimeter. From the positive terminal to the engine block I have the same 12.23V. The sarter will not turnover the engine unless I use jumper cables. I have replaced the battery cables...

On the 2004 Edge rear springs did they have a factory lift block and how thick was it? If anyone has a photo that would be great. Thanks, Nomad

My 1989 STX 4x4 ranger with a 2.9 v6 ran fine, then it sat for 3 weeks or so, went to start it and the battery was almost dead. I started it and it ran for 20 seconds and died, tried to restart and nothing. also, my gas gage was not working so I replaced the sending uint/ Fuel pump and fuel pump...

I have a 1989 Ranger STX 4x4 2.9 V6 and I need a fuel pump sending unit. The ford dealer wants $465.00 and Pepboys wants $100.00, each have a 1 year warranty. Is the ford unit that much better or is there an alternate sorce for a factory unit? Has anyone used an aftermarket unit with good...

I have a 1989 Ranger STX running 31" x 10.50 tire with 2.9 V6 and 5 speed , I need to regear. I'm looking for feed back from people with 31" tires and 4.10 or 4.56 gearing. I know the 4.10 would be better for the highway- but off road the 4.56 would be better. What kind of RPM s are running 65...

The other day my fuel gage stopped working; then a few days later my truck would start, run a few seconds and then die. 2 years ago i replace the sending unit, filter, and fuel pump relay- I had a extra relay and installed but it did not fix the problem. I have not checked the fuel pressure at...

1. What is the spring rate of the Skyjacker 4" springs? 2. Are they stiff enough to run without a swaybar? 3. With a 4" lift on a "High Rider" will the pitman arm need to be replaced with a 4" drop? 4. Whats the best locking diff for the Ford 7.5? Thanks