i've been searchin and really haven't found my answer. but anyways i swapped an 8.8 from an 01 explorer into my 03 ranger. i was wondering what you guys have used or done to get the ebrake cables to work together?
it happened pulling out of my garage.. i had to use a prybar to pop it back up. i read on pirate that u measure the flat length of springs - shackle length + 1/2" = the distance from bolt hole to bolt hole on the 2 hangers. so 63"-4.5"+1/2"=59". they are currently at 60.5" which is what i got...
ok so i'm almost done with my sas on my 03. i have a toyota steering box (which is about all i could find that would fit). those of you guys that have done it, the pitman arm has the tie rod end on it.. how do i go about punching a hole in it for my 1 ton chevy tre? i have a reamer for it i just...
anybody see these yet.
http://compare.ebay.com/like/390251415827?var=lv<yp=AllFixedPriceItemTypes&var=sbar&rvr_id=182311007031&crlp=1_263602_309572&UA=%3F*F%3F&GUID=1d92b0121290a06c1c470767ffc1f9b7&itemid=390251415827&ff4=263602_309572
looks similar to the lock-right. anybody have one?
Ok so i got bored with my old build cuz it was taking me too long. I came across this so i decided to go another route. $1,500 for an 03 4x4 couldn't pass it up.
Here is the link to the old thread. still the same idea just a reg cab instead of an xcab. and i'm going to do a flat/tube bed...
it does it in ac and heat. my dads focus has the same problem. the heat or ac can be on but the fan will only work on the highest power. any suggestions? dad put a new switch in his and it didn't fix it. i may have another gage cluster layin around i'm gonna try but i thought i'd ask to see if...
whats everybody using and how do you like it. i've seen some toyota boxes and eb, but are there any other options? thats were i'm at on my build and not finding a lot of info on it
i'm going for the lockrite or the aussi locker and 5.13 gears for my 8.8 31 spline and d44.
the 8.8 lockers all read they are for open diffs, mine is limited slip. can i use the carrier out of my 28 spline 8.8 that came off the ranger.
i have a 98 i sas'ed and swapped to a 5 speed. what years can i pull the haness and computer from and keep it plug and play?? or do i really need a new harness??
i'm headed to hilton head for the first time and i'm tryin to decide if i wanna take the ranger or not. i googled it and found carolina beach but thats too far away, other than that the other one was outer banks.
thanks guys
i bought it yesterday. i already changed the carpet out. it was nasty. its a lil rusty but the cab is all good. i'm gonna merge this one in with the sas i've been workin on. i just got tired of messin with the body on the other one. my plan is to swap this cab down on the other frame, once i...
there needs to be a tech write up on this. people r claiming they have done it without changing the core support, but i can't find any pics. i'm going to start one on my 96, if there isn't one by then i guess i will have to write one up :headbang:
ok i know it been covered but i'm not finding the answer i need. i am swapping in a m5od on my 98 4.0 4x4. what years m50d will fit my 4.0? i think it was 96ish when they went to the sohc, and i remember the bell housing is different. just want to make sure before i buy anything i cant use...
will this work on my 94? it says till 90 and it looks right. mine is rotted up and hardly holds contact
http://www.repairconnector.com/index.cfm/fa/items.main/parentcat/26462/subcatid/0/id/419403
ok just like it says. the motor mounts are different and further apart on the frame. i thing the 98 they are almost 18" apart and on the 93 they are about 16" apart and one sits higher than the other. i was reading another thread and it said to change out the brackets on the motor. but i don't...
ok so i have some wiring issues and i thought i remembered seeing diagrams on this site before but i cant find them. soo i'll ask and see if i can get any answers.
a little background on my truck.
98 ranger wrecked i wanted to do an sas so i found a 93 frame, and had to put a 97 gas tank on...
ok the the first 3 gen rangers use a steerin box the newer ones use a rack setup. the shaft i have off of the 98 is obviously too long, would swapping in an earlier shaft work or do i need to swap steering column out as well. the steering column looks like it points down too much because of how...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.