My 91 Exploder

7.5L_STX · Mar 2, 2011

Foxracin said:
Not in the plans right now but never know. Might decide to do it one day.

I do have some inserts coming from Ballistic Fab to weld in the knuckles to move the tie rod on top of the knuckles so it will move the tierod up around 3-4 inches.

Link? i cant seem to find em.

Edit: nevermind, i think i found em. are they listed as Tapered GM TRE inserts? if so , do they work fine with the ford TREs?

Foxracin · Mar 2, 2011

Im using 1 ton GM tre's so dont know if they will work with fore tre's or not.

Foxracin · Mar 6, 2011

Doubler is in. I officaly have a mall crawler now. It will definitely crawl and it temporarily 2wd until I get to build the trans crossmember.

Got it all in today and make the shift handles. Double low is badass. Cant wait to get it out and do some wheeling.

Had to get the bfh out on the floorboard.

Got room for it now.

Shifters and double boot. Still got to cut the shifters to length and thread them for some knobs so dont mind them yet.

2 high

4 double low

Going to run to Napa tomorrow and see about getting a new longerspeedometer cable so the speedo will work again.

Boggin · Mar 6, 2011

that is sweet

Boggin · Mar 7, 2011

i nominated you for totm

http://therangerstation.com/forums/showthread.php?p=961969#post961969

vote!

Foxracin · Mar 10, 2011

Well was about to order a set of chromo shafts for the front the other day and ran across this for a deal. ARB for the d44. Got it from bronco2guy. Going to save up a little more cash and get some chromo axles next.

Came in the mail today.

Also got a new speedo cable from Napa today. Stock one was too short with the doubler. Its for a 91 Aeroster and has the same ends and is about 8" longer. Works prefect.

Shows how much longer the stock.

Grunizzle · Mar 10, 2011

damn I am jealous.. good work man I am looking forward to some wheeling reports

Josh40601 · Mar 10, 2011

oh how i want an ARB or E-Locker

Foxracin · Mar 11, 2011

Had a crossmember fabbed up today. Not a lot of room to work with under there with the driveshaft and exhaust in the way and wanting to keep it tucked up in the frame. lol

Pics suck.

--weezl-- · Mar 11, 2011

that crossmember looks sick!

Foxracin · Mar 21, 2011

Got my shifter knobs for the doubler today so pulled the shifters out and cut them down and threaded the ends for the knobs.

Got a trip planned to Mountain City, TN next weekend to test it out finally. Going to try to get some new rock sliders put on this weekend.

Boggin · Mar 21, 2011

those twin sticks look badass, very nice work. also everyone go vote for this explorer in the TOTM lol

kroussinoffroad · Mar 21, 2011

where did ya get the knob's?

Josh40601 · Mar 21, 2011

damn its looking good buddy. Good luck in the TOTM. (pss.... you got vote :icon_thumby:

)

CountryBoy78 · Mar 21, 2011

x2 ^^^^

My 91 Exploder

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

01/2013 OTOTM Winner

Well-Known Member

Well-Known Member

June 2011 OTOTM Winner

Well-Known Member

Well-Known Member

October 2011 OTOTM Winner

Well-Known Member

Well-Known Member

Similar threads

Sponsored Ad

Sponsored Ad

TRS Events

Member & Vendor Upgrades

Recently Featured

Ranger Adventure Video

TRS Merchandise

Follow TRS On Instagram

TRS Sponsors

Sponsored Ad

Sponsored Ad

Amazon Deals

Sponsored Ad