• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Front axle issue


4x4cameron

New Member
Joined
Nov 4, 2007
Messages
4
Reaction score
0
Points
0
Age
45
Vehicle Year
1988
Make / Model
Ford
Transmission
Manual
I have a 1988 Ranger with stock axles and a lift.
This tuck has seen over 5,000 miles trail riding and slap wore out.
Problem is the front axle right near wheel where the u-Joint is has a lot of play. I can rock it up and down a few inches. My 4x4 has quit and I believe the axle shaft is not engaging with hub. The play is so bad the truck will vibrate at high speeds.
Can someone tell me how to fix this problem?
 


Mutant Pony

Mutant Pony

Active Member
V8 Engine Swap
Solid Axle Swap
Joined
Aug 6, 2007
Messages
1,753
Reaction score
9
Points
38
Age
58
Location
Hersey, Mi
Vehicle Year
1977
Make / Model
Ford
Engine Size
2300
Transmission
Manual
There is supposed to be a bearing on the inside of the spindle. Yours doesn't have one anymore. You will need a new axle stub now that it has been neglected that long. The bearing and seal kit is cheap though.
 

4x4cameron

New Member
Joined
Nov 4, 2007
Messages
4
Reaction score
0
Points
0
Age
45
Vehicle Year
1988
Make / Model
Ford
Transmission
Manual
So I need a new bearing and seal kit and the axle shaft is ok or replace that too.
How do I replace it?
Could this also cause the 4x4 to bind up when turning sharp?
 
Mutant Pony

Mutant Pony

Active Member
V8 Engine Swap
Solid Axle Swap
Joined
Aug 6, 2007
Messages
1,753
Reaction score
9
Points
38
Age
58
Location
Hersey, Mi
Vehicle Year
1977
Make / Model
Ford
Engine Size
2300
Transmission
Manual
You need to remove the Wheel, caliper, Rotor, Spindle, Axle. Then you will need to replace the outer axle(might as well include a u-joint). The spindle may be ruined on the inside, You may need one. If not, you need to replace the inner spindle bearing.
Yes this will cause the lock out not to work and the only reason for the axle to move up and down.
 

4x4cameron

New Member
Joined
Nov 4, 2007
Messages
4
Reaction score
0
Points
0
Age
45
Vehicle Year
1988
Make / Model
Ford
Transmission
Manual
You have been very helpfull.
Can you give me a guess on price if spindle is trashed and outer axle
Also would this problem cause 4x4 to bind up when turning wheel.
I mean bind so hard can hardly move truck then it made snap sound?
 
4x4junkie

4x4junkie

Forum Staff Member
TRS Forum Moderator
TRS 20th Anniversary
Joined
Aug 19, 2001
Messages
10,755
Reaction score
583
Points
113
Location
So. Calif (SFV)
Vehicle Year
1990
Make / Model
Bronco II
Engine Type
2.9 V6
Engine Size
2.9L V6
Transmission
Manual
2WD / 4WD
4WD
Tire Size
35x12.50R15
A bad spindle needle bearing can cause it to bind like that, yes. So can a frozen u-joint.
 
You must log in or register to reply here.

Sponsored Ad


Sponsored Ad

Staff online

Members online

Total: 678 (members: 9, guests: 669)

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

Latest Album Photos

Hunters
20240409_190831.jpg
20240409_190818.jpg
20240409_180824.jpg
20240409_182648.jpg
20240409_181010.jpg
20240408_175026.jpg
99 Ranger
20200706_161414.jpg
20240207_155117.jpg
20240207_155111.jpg
20240207_154537 - Copy.jpg

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top