mjonesjr
03-10-2009, 02:42 PM
Original Poster: The H.P. Freak
Difficulty: _ out of _
Time to install:
As you know the newer Rangers ('02+) only have a turn signal bulb in the front head light assembly. Well this mod turns the corner marker light into a turn signal as well. This mod allowing more visibility of your turn signals to other motorists.
Here's a few pics :
Here is the stock set-up from the factory on the D/S.
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0988.jpg?t=1233020041
The BLACK/YELLOW (black wire with yellow stripe) needs to be cut. Make sure to leave enough wire so that this mod can be reversed if desired.
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0989.jpg?t=1233020210
I used weather tight male/female electrical connectors for a cleaner look plus it would be very easy to return to stock later if I wanted to. The dead end of the wire got a opposite connector, and I simply used another connector to block it off. I then used some shrink tubing to make it water resistant.
Now I took the other end of the wire and tapped it into the PURPLE/GREY (purple wire with grey strip). This would be the bottom wire out of the 3 wires on the turn signal harness with the quick clip facing up.
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0997.jpg?t=1233020469
It should look like this :
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0994.jpg?t=1233020633
This is the finished product after everything was taped back up :
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM1003.jpg?t=1233020642
Difficulty: _ out of _
Time to install:
As you know the newer Rangers ('02+) only have a turn signal bulb in the front head light assembly. Well this mod turns the corner marker light into a turn signal as well. This mod allowing more visibility of your turn signals to other motorists.
Here's a few pics :
Here is the stock set-up from the factory on the D/S.
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0988.jpg?t=1233020041
The BLACK/YELLOW (black wire with yellow stripe) needs to be cut. Make sure to leave enough wire so that this mod can be reversed if desired.
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0989.jpg?t=1233020210
I used weather tight male/female electrical connectors for a cleaner look plus it would be very easy to return to stock later if I wanted to. The dead end of the wire got a opposite connector, and I simply used another connector to block it off. I then used some shrink tubing to make it water resistant.
Now I took the other end of the wire and tapped it into the PURPLE/GREY (purple wire with grey strip). This would be the bottom wire out of the 3 wires on the turn signal harness with the quick clip facing up.
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0997.jpg?t=1233020469
It should look like this :
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM0994.jpg?t=1233020633
This is the finished product after everything was taped back up :
http://i361.photobucket.com/albums/oo58/Neal330ci/2007%20RANGER%20TURN%20SIGNAL%20MOD/HPIM1003.jpg?t=1233020642