• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

2000 mountaineer no start


erikm

Member
V8 Engine Swap
Solid Axle Swap
Joined
Aug 6, 2007
Messages
115
Reaction score
0
Points
16
Location
Iowa
Vehicle Year
1995
Make / Model
Ford
Engine Size
5.0L
Transmission
Automatic
hey, my 2000 mountaineer cranks but will not start. the "fuel reset" light comes on when turning the ignition switch to "run"...it has never done this before. it was fine, i drove home, shut it off then 2 hours later it wouldn't start. it did start up an run for about 10 seconds then nothing, like it was out of fuel but it has plenty in the tank. any ideas??
 


Earl43P

Well-Known Member
U.S. Military - Veteran
Joined
Aug 7, 2007
Messages
3,159
Reaction score
38
Points
48
Location
Farmington, Pa
Vehicle Year
2019
Make / Model
Ford F250 4WD
Engine Size
3.0
Transmission
Manual
That light is for the Inertia Switch, meaning it has tripped. It removes power from the fuel pump in an impact.

It should be in the PS footwell, right about where the passenger's toes hit the incline (pull the carpet back). Push the red reset button.

It may need replaced. Cheap part.
 

erikm

Member
V8 Engine Swap
Solid Axle Swap
Joined
Aug 6, 2007
Messages
115
Reaction score
0
Points
16
Location
Iowa
Vehicle Year
1995
Make / Model
Ford
Engine Size
5.0L
Transmission
Automatic
kinda weird it tripped sitting in the driveway....i will check that out.

thanks....

That light is for the Inertia Switch, meaning it has tripped. It removes power from the fuel pump in an impact.

It should be in the PS footwell, right about where the passenger's toes hit the incline (pull the carpet back). Push the red reset button.

It may need replaced. Cheap part.
 

Earl43P

Well-Known Member
U.S. Military - Veteran
Joined
Aug 7, 2007
Messages
3,159
Reaction score
38
Points
48
Location
Farmington, Pa
Vehicle Year
2019
Make / Model
Ford F250 4WD
Engine Size
3.0
Transmission
Manual
Read your Owner's manual, should be in there!

And the switch could be bad. Again, it's an easy, cheap part.
 

erikm

Member
V8 Engine Swap
Solid Axle Swap
Joined
Aug 6, 2007
Messages
115
Reaction score
0
Points
16
Location
Iowa
Vehicle Year
1995
Make / Model
Ford
Engine Size
5.0L
Transmission
Automatic
so if it is the inertia switch, can i just bypass it for now? does it have a fuel pump test terminal like the older fords? if so where would be located? sorry for all the ?? but i have to go 25 miles out in the country to try and get it going for my ex-wife and would like to take what ever i can think of to get it going for her.
 

erikm

Member
V8 Engine Swap
Solid Axle Swap
Joined
Aug 6, 2007
Messages
115
Reaction score
0
Points
16
Location
Iowa
Vehicle Year
1995
Make / Model
Ford
Engine Size
5.0L
Transmission
Automatic
well, i don't know what to make of this! "fuel reset" light comes on with ignition in "run" ....i hear the fuel pump come on, crank and boom it starts!! tried it several times with only one failure, it started and then died like no fuel, every other time it started just fine.




That light is for the Inertia Switch, meaning it has tripped. It removes power from the fuel pump in an impact.

It should be in the PS footwell, right about where the passenger's toes hit the incline (pull the carpet back). Push the red reset button.

It may need replaced. Cheap part.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top