• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

No Clutch At All.....


Joined
Dec 9, 2008
Messages
4
Reaction score
0
Points
0
Vehicle Year
All
Make / Model
All
Transmission
Automatic
Hello there,
Vehicle: 1997 Ford Ranger XLT 6cyl.
Problem:After Pulling the Trany, resurfacing the fly wheel & installing a new pressure plate. I cannot get any pedal at all under normal conditions! The only time I CAN get pedal is when a pressure bleeder is in place. Only then does the clutch work properly.
I have replaced the following:
-clutch M/C
-Slave M/C
-Clutch-tranny fluid line

So what is my problem?????
Or probably more to the point, what am I being an IDIOT about?
 


fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
8,016
Reaction score
2,832
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
Check this thread. Pretty sure you're dealing with the same thing.
 
Joined
Dec 9, 2008
Messages
4
Reaction score
0
Points
0
Vehicle Year
All
Make / Model
All
Transmission
Automatic
Thanks fastpakr!!
I am on the fence with this whole "air in the line" direction. The reason for my hesitance is that I have a "pressure bleeder" in place. While that unite is IN, I have great pedal! As soon as I remove it & put the regular M/C cap back on, I loose all pedal. So I am wondering if "air" is really the problem. Any advice or alternate information sources are greatly appreciated.
Thanks,
Jason
 

4x4RangerGuy

New Member
Joined
Aug 7, 2007
Messages
809
Reaction score
5
Points
0
Age
39
Location
Newton Highlands, MA
Vehicle Year
2003
Make / Model
Subaru
Engine Size
2.0
Transmission
Manual
Did you bench bleed the master cylinder? I'd start with that; it needs to be out of the truck to bleed it properly. After that, bleed the slave manually, don't use a pressure bleeder it won't work well. Also, did you notice any brake fluid when you pulled the transmission?
 

fastpakr

Forum Staff Member
TRS Event Staff
TRS Forum Moderator
Supporting Member
Article Contributor
U.S. Military - Veteran
V8 Engine Swap
TRS 20th Anniversary
TRS Event Participant
Joined
Aug 6, 2007
Messages
8,016
Reaction score
2,832
Points
113
Location
Roanoke, VA
Vehicle Year
1999
Make / Model
Ford
Engine Type
V8
Engine Size
5.0
Transmission
Automatic
2WD / 4WD
4WD
Tire Size
285/75-16
The master does not need to be out of the truck, nor should that even be considered. It is both easier and more effective to simply leave it in the truck, but unbolted from the firewall and therefore easy to rotate so the air can escape. Bleed it by pushing the piston manually. Route the slave bleeder line into the master reservoir and just leave it open until you're convinced the air is out, then close it and test. Quick and easy (other than the part about unbolting the master, which still isn't terrible.
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Shran
April Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top