can you get a double din to fit in an 06?
- Thread starter stoop
- Start date
- Joined
- Aug 9, 2007
- Messages
- 451
- Points
- 3,101
- City
- Lawrenceburg, IN
- Vehicle Year
- 2024
- Engine
- 2.0 (4 Cylinder)
- Transmission
- Automatic
More than likely you will need an installation kit to make it work.
- Joined
- Jul 17, 2008
- Messages
- 30
- Points
- 3,101
- Age
- 41
- City
- Louisiana
- Vehicle Year
- 2007
- Transmission
- Automatic
It's been done. Basically it involves cutting/dremeling around the dash to increase the size from 1.8 DIN to Double DIN. I've never done it...yet (I want to locate some spare parts before I attempt so I don't screw up my dash,) but if you google it, I'm sure you'll get a lot of info.
- Joined
- Nov 22, 2008
- Messages
- 4
- Points
- 3,001
- City
- Atlanta, GA
- Vehicle Year
- 2005
- Transmission
- Automatic
A double din radio will fit. Check out metraonline.com or scosche.com for the double din dash kit you need to accomodate the new head unit.
All you need for the kits is a screwdriver to remove the radio bezel and screws holding the radio in, a panel popper, and a pair of plyers to remove any unneccessary tabs from the dash kit.
Both companies include detailed removal/installation instructions for the vehicles. A Ranger kit usually runs around $21.99.
All you need for the kits is a screwdriver to remove the radio bezel and screws holding the radio in, a panel popper, and a pair of plyers to remove any unneccessary tabs from the dash kit.
Both companies include detailed removal/installation instructions for the vehicles. A Ranger kit usually runs around $21.99.
- Joined
- Nov 23, 2008
- Messages
- 8
- Points
- 3,001
- Vehicle Year
- 2008
- Transmission
- Automatic
its possible
Yup it is possible. i just put the pioneer avec d3 into my 08 which is pretty much the same. you cant really buy a kit for it exept the wiring harness there is no cutting the dash but the is 2 very small cuts you need to make on the panel as for setting the deck it needs to be custom i used 2 strips of metal and mounted them where the screw holes are that hold the panel in then measured the strips to the sides of the deck and screwed everything in. it worked great and it makes it almost impossible for theves to steal it. if you have anymore questions let me know...
Yup it is possible. i just put the pioneer avec d3 into my 08 which is pretty much the same. you cant really buy a kit for it exept the wiring harness there is no cutting the dash but the is 2 very small cuts you need to make on the panel as for setting the deck it needs to be custom i used 2 strips of metal and mounted them where the screw holes are that hold the panel in then measured the strips to the sides of the deck and screwed everything in. it worked great and it makes it almost impossible for theves to steal it. if you have anymore questions let me know...
- Joined
- Nov 23, 2008
- Messages
- 8
- Points
- 3,001
- Vehicle Year
- 2008
- Transmission
- Automatic
no but i can take most of it apart a take pics ill put them up tomorrow..
- Joined
- Nov 20, 2008
- Messages
- 9
- Points
- 3,001
- Vehicle Year
- 2006
- Transmission
- Manual
OK, so I have completed my intall. Fitting a double DIN is an easy job. A little has to be trimmed from the inside (which is not visable after the head unit is installed) of the dash slot. Use a dremmel with a cut off disc or a sharp OFLA knife. I used a scoche (sp?) dash kit which fit nice. Also if anyone is having troubles tring to view DVDs while on the road, ground the ebrake wire on the head unit and use a switch to interupt that wire. The new head units must be connected to ground then not connected to ground, hense the use of the switch.
im a little late but saw you wanted pics heres mine in a 95
Sponsored Ad
TRS Events & Gatherings
Latest posts
-
Specific Radio Boss (note not Bose, but Boss) 632UAB- Latest: Li'l Work Truck
-
-
-
-
-
-
-
-
-
Featured Rangers
TRS Latest Video
Official TRS Merchandise
Follow TRS On Instagram
