• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Spark Plugs and wires on a SOHC 4L.


Ranger44

New Member
Ford Technician
Joined
Aug 13, 2007
Messages
3,127
Reaction score
23
Points
0
Location
Illinois
Vehicle Year
1995
Make / Model
FORD
Engine Size
4.0 OHV
Transmission
Automatic
This is in request for simple basic maintenance guides by Jim. Here we go.

It can be used as a guide for most engines, but specific to the SOHC 4.0.

Submitted by: Ranger44

Difficulty: 6 out of 10.

Spark plugs used and recommended by FORD:



The driver's side is pretty much straight forward, you can get at it through the top.



Use a pair of pliers or spark plug pliers to remove the plug wires from the 1st spark plug. It's best to remove one plug and wire at a time. That way nothing gets mixed up and you can ensure everything is routed the same way it was removed.

Use a 5/8 spark plug socket to remove the first plug (cylinder #4).





Be sure to check and see that the spark plug gap is correct on your plugs. The gap spec given on the radiator support said .062-.068. With these fine wire platinums it's not a good idea to jam feeler gauges in there. So do your best to get it close, most of the time with the Motorcraft stuff it's dead on. All mine where surprisingly. I used an old autolite to give an example.





Install the new plug. Try not to bang the tip on anything while putting it in the socket, this CAN throw the gap off. When tightening the plug, don't crank on it. It only needs to be tightened to 13 ft/lbs, in other words..... snug with a socket and 3/8 ratchet.



Then take off the wire completely, and match it to one in the kit.

Plug wires I used:



Install the NEW wire, following the route the old one used, and laying it into the plastic guides/retainers........

Repeat with cylinders #5 and #6. Then move to the passenger side for cylinders #1-#3.

Big tip for the driver's side.

Break your front passenger wheel loose.





Jack up the front of the truck.



Add jackstands to the nifty little hooks on the front of the lower control arms, and let the truck rest on the stands.



Remove your wheel. Now check out the removable fender apron.....



Remove the christmas tree fasteners and the apron.



Ta da!



Repeat what happened on the other side, but try and keep your sanity. It took me a little while longer on this side. It's a constant battle of using different combinations of 3/8 ratchet (standard and flex head), extentions and swivels. AND going from top, to fenderwell and back in order to complete the job. You'll get it, but it'll just try your patients.

Make sure all your wires are ran:



Fire her up and check for proper operation........

If there is a miss check for disconnected wires, or plug wires not seated all the way. After that double check proper coil order to cylinder order.



If there are any questions please ask. It will only benefit to the article.

Thanks,

Ryan
 


_@_

New Member
Joined
Dec 17, 2009
Messages
33
Reaction score
0
Points
0
Location
NJ
Vehicle Year
2002
Make / Model
ford
Engine Size
4.0
Transmission
Automatic
How much did that stuff cost? How long did it take you?
 

Sasquatch_Ryda

Well-Known Member
Ford Technician
OTOTM Winner
Solid Axle Swap
Forum Staff - Retired
TRS Banner 2012-2015
Joined
Aug 8, 2007
Messages
7,916
Reaction score
108
Points
63
Age
36
Location
Terrace, BC, Canada
Vehicle Year
1991
Make / Model
Ford
Engine Type
4.0 V6
Engine Size
4.0L
Transmission
Automatic
2WD / 4WD
Solid Axle Swap 4x4
Tire Size
40s
Another thing to add....its not a bad idea to blow out around all the plugs with compressed air before removal to get any dirt/debris out of there before you pull the plug and let it drop into the cylinder.
 

Ranger44

New Member
Ford Technician
Joined
Aug 13, 2007
Messages
3,127
Reaction score
23
Points
0
Location
Illinois
Vehicle Year
1995
Make / Model
FORD
Engine Size
4.0 OHV
Transmission
Automatic
How much did that stuff cost? How long did it take you?
Rockauto has good prices on the motorcraft plugs and wires.

Another thing to add....its not a bad idea to blow out around all the plugs with compressed air before removal to get any dirt/debris out of there before you pull the plug and let it drop into the cylinder.
Yes, thankyou for adding. A blow gun from shop air or even air in a can could work. Of coarse shop air will be more effective.
 

Jim Oaks

Just some guy with a website
Administrator
Founder / Site Owner
Supporting Vendor
Article Contributor
TRS Banner 2010-2011
TRS Banner 2012-2015
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Aug 2, 2000
Messages
13,407
Reaction score
8,527
Points
113
Location
Nocona, Texas
Vehicle Year
1996 / 2021
Make / Model
Ford Ranger
Engine Type
4.0 V6
Engine Size
4.0 / 2.3 Ecoboost
Transmission
Automatic
2WD / 4WD
4WD
Total Lift
6-inches
Tire Size
33x12.50x15
Added to online magazine.

Thanks!
 

Ranger44

New Member
Ford Technician
Joined
Aug 13, 2007
Messages
3,127
Reaction score
23
Points
0
Location
Illinois
Vehicle Year
1995
Make / Model
FORD
Engine Size
4.0 OHV
Transmission
Automatic

Sponsored Ad


Sponsored Ad

Members online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top