• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

wiring harness compatibility


scrapper

Active Member
Supporting Member
U.S. Military - Veteran
V8 Engine Swap
Joined
Nov 27, 2008
Messages
512
Reaction score
63
Points
28
Location
central IL
Vehicle Year
1994
Make / Model
ford
Engine Type
V8
Engine Size
1975 302
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
6+3
Tire Size
33/12.50/15
I have a 94 but are there other years that have the same harness going to the engine? It would seem to be 2 different harnesses 1 that goes to injectors and one goes to most everything else. Mine seems to be having problems with several bad wires and , it has been a bit since I messed with it but the ground is bad for sure,looks oxidized. I hate to put used wire back in but not even sure what part numbers to look for. If I could look for a couple different years may be easier?Thanks for any help. I really dont want to try an build one.
 


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,292
Reaction score
8,298
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
1994 was last year for the 60 wire EEC-IV computer, so it would have to be an older harness, 1989-1994

I don't think there were many changes in those years on the 2.3l Lima Rangers
 

scrapper

Active Member
Supporting Member
U.S. Military - Veteran
V8 Engine Swap
Joined
Nov 27, 2008
Messages
512
Reaction score
63
Points
28
Location
central IL
Vehicle Year
1994
Make / Model
ford
Engine Type
V8
Engine Size
1975 302
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
6+3
Tire Size
33/12.50/15
ok I thought 93-94 were really the same but may have a couple of different pins? Thanks for an answer
 

scotts90ranger

Well-Known Member
RBV's on Boost
Joined
Feb 28, 2001
Messages
7,936
Reaction score
4,231
Points
113
Location
Dayton Oregon
Vehicle Year
1990, 1997
Make / Model
Ford
Engine Type
2.3 (4 Cylinder)
Engine Size
2.3 Turbo
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6
Tire Size
35"
'93-94 are basically the same, both have the EGR flow sensor and MAF, '90-92 had an EGR position sensor and MAF and '89-early '90 had a MAP sensor and EGR position sensor unless atuomatic transmission then no EGR. '89 had neutral sensor in the trans but that got dropped around '90 I think (my '89 donor had it, '90 body did not which was built in '89 and had MAP not MAF). There's various changes around '92 related to the trans and dash wiring, even my '89 and 90 swap project I did like 15 years ago had some pinout differences between the two...
 

scrapper

Active Member
Supporting Member
U.S. Military - Veteran
V8 Engine Swap
Joined
Nov 27, 2008
Messages
512
Reaction score
63
Points
28
Location
central IL
Vehicle Year
1994
Make / Model
ford
Engine Type
V8
Engine Size
1975 302
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
6+3
Tire Size
33/12.50/15
There arent any pinouts for a 94 2.3 in the tech section. I may just get a whole harness off ebay and replace it all. They are under 200. bucks and new. I'm planing on putting a carbed 302 in it but was looking for an easy wiring solution. I'm color blind and hate doing anything that resembles wiring...
 

Sponsored Ad


Sponsored Ad

Staff online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Latest posts

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top