• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

What is this component on the back of a 1999 4.0L? Looks like it is in what was the Distributor hole on the older Gen engines?


BillRod

Member
Joined
Dec 27, 2008
Messages
219
Reaction score
1
Points
18
Location
Colorado Springs CO
Make / Model
Ford
Engine Size
95=4.9L Others=4.0L
Transmission
Manual
Hi All

What is this component?
It is in what looks like the Distributor hole of the older Gen trucks.

Thanks
Bill
 

Attachments

Last edited:


RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
That's the Cam synchronizer with cam sensor on top, but if its a 1999 it should have the 2 wire cam sensor, so its a 1998 or earlier

Yes, while the 4.0l OHV never had a distributor this unit operates the same way, its driven by a gear on the cam and also Drives the oil pump, so an important part
It also needs to be "timed" like a distributor was
 

BillRod

Member
Joined
Dec 27, 2008
Messages
219
Reaction score
1
Points
18
Location
Colorado Springs CO
Make / Model
Ford
Engine Size
95=4.9L Others=4.0L
Transmission
Manual
The pic is the engine from a rolled Ranger I bought to pull the engine and use it to replace the blown engine in my son's 2000 Explorer.
Ranger was titled as a 99, Engine is a 3Yr old 4.0 OHV Re-manufactured engine.
Called a few salvage yards to verify and was told that 98, 99 & 2000 OHV engines were interchangeable.

Turns out the Harnesses were not the same. Ranger had the connector near the top of the bell housing for the trans but the explorer did not so had to leave the Explorer harness in the truck and remove the complete ranger harness from the Ranger engine.
The Oil Pressure sender had a different connector so we swapped the senders.

The Ranger engine Cam Synch has the 3 Pin. The Explorer harness has the 2 Pin.
Pretty sure this is the only other component other than the oil sender that has a different connector.

I assume that I should put both engines #1 Cyl at TDC before I swap the Cam Synchronizers between the two so that it is easier to re-time once the engine is installed?

Any other advice would be greatly appreciated.

Thanks
Bill
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual

BillRod

Member
Joined
Dec 27, 2008
Messages
219
Reaction score
1
Points
18
Location
Colorado Springs CO
Make / Model
Ford
Engine Size
95=4.9L Others=4.0L
Transmission
Manual
Does anyone make an adapter so I can avoid having to swap the units between engines?
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
If you are referring to the Cam sensor then no
The 3 wire is a hall effect sensor, so 12volt DC on/off signal
The 2 wire is a VR(variable reluctance) sensor, AC Volt signal, a frequency(Hz) signal, AC volts generated by the sensor

There would be no way to convert these signals in any consistent manner at even close to the cost of swapping them out

You don't need the Cam sensor for engine to run and drive, it would just set a code
 
Last edited:

rubydist

Well-Known Member
TRS Forum Moderator
Joined
Dec 16, 2016
Messages
985
Reaction score
835
Points
93
Location
Denver
Vehicle Year
2009
Make / Model
Ford Ranger FX4
Engine Type
4.0 V6
Transmission
Automatic
2WD / 4WD
4WD
But if the current sensor is timed properly, all you should have to do is remove that sensor and install the correct one without having to change any timing.
 

Shran

Junk Collector
TRS Forum Moderator
Supporting Member
Article Contributor
V8 Engine Swap
Solid Axle Swap
Joined
Mar 4, 2008
Messages
8,636
Reaction score
4,703
Points
113
Location
Rapid City SD
Engine Type
V8
Engine Size
5.0
But if the current sensor is timed properly, all you should have to do is remove that sensor and install the correct one without having to change any timing.
The sensors are not necessarily interchangeable. More likely in a newer truck but it may not just be a matter of swapping sensors... May need the whole synchronizer.
 

RonD

Official TRS AI
TRS Technical Advisor
Joined
Jun 2, 2012
Messages
25,290
Reaction score
8,290
Points
113
Location
canada
Vehicle Year
1994
Make / Model
Ford
Transmission
Manual
You for sure need the whole unit when swapping from 3 to 2 wire or visa versa
 

Sponsored Ad


Sponsored Ad

Staff online

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top