• Welcome Visitor! Please take a few seconds and Register for our forum. Even if you don't want to post, you can still 'Like' and react to posts.

Welding cat to muffler at flange?


ecgreen

Well-Known Member
Joined
Sep 21, 2018
Messages
720
Reaction score
287
Points
63
Location
Dunbarton NH
Vehicle Year
1989
Make / Model
Ford Bronco II
Engine Type
2.9 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
3"
Tire Size
33
So I can't for the life of me get the muffler flange to seal tight to the cat ouptut flange on my 89 Bronco II. I have tried a variety of gaskets to no avial - it alwasy leaks out of the bottom where the two flanges meet. Can anyone thing of a reason not to just weld the two together?
 


ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,215
Reaction score
16,352
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
I can think of a reason. But the reality is, if that’s what you have to do, then that’s what you have to do. It just means that you might have to cut it apart some day.
 

ecgreen

Well-Known Member
Joined
Sep 21, 2018
Messages
720
Reaction score
287
Points
63
Location
Dunbarton NH
Vehicle Year
1989
Make / Model
Ford Bronco II
Engine Type
2.9 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
3"
Tire Size
33
my only worry is that I believe that joint is suppose to flex. If I weld it, the stress will be where the y-pipe connects to the cat. That is a strong ass flange point though. I dont know, I think too much
 

ericbphoto

Overlander in development
TRS Event Staff
TRS Forum Moderator
Supporting Member
U.S. Military - Veteran
TRS 20th Anniversary
VAGABOND
TRS Event Participant
GMRS Radio License
Joined
Feb 7, 2016
Messages
15,215
Reaction score
16,352
Points
113
Age
59
Location
Wellford, SC
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
3.0 V6
Engine Size
3.0L
Transmission
Manual
2WD / 4WD
4WD
Total Lift
6"
Tire Size
35"
My credo
In theory, theory and practice are the same. In practice, they are different.
If the joint is loose enough to flex, its loose enough to leak. If you want a place for stuff to flex, install a piece of flex pipe.
 

BlackBII

Ranger Custom
Article Contributor
OTOTM Winner
TRS Banner 2010-2011
Truck of Month
Joined
Aug 14, 2007
Messages
7,895
Reaction score
982
Points
113
Location
UT
Vehicle Year
1989
Make / Model
Ford
Engine Type
4.0 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
5
Tire Size
33
I replaced that connection on my Ranger with some header collector flanges. It's been working great.

Patriot Exhaust H7259 is what I used. It's for 2.5" pipe, but I was able to get some pipe reducer adapters at Autozone since the factory pipes aren't that large.

 

19Walt93

Well-Known Member
Ford Technician
V8 Engine Swap
Joined
Nov 13, 2018
Messages
4,475
Reaction score
4,412
Points
113
Location
Canaan,NH
Vehicle Year
1993
Make / Model
Ford Ranger
Engine Type
V8
Engine Size
351
Transmission
Automatic
2WD / 4WD
2WD
Total Drop
3"
Tire Size
235/55R16
My credo
If you don't have time to do it right will you have time to do it over?
I like the bell flare connectors Walker makes better- no gaskets and you can swivel it around to suit you. I weld the male end of the connector to the pipe in front and the female end to the rear section but you could switch it if you want. I couldn't find a picture of the male end but the lower right piece is the female end. No more leaky gaskets.
39069
 

ecgreen

Well-Known Member
Joined
Sep 21, 2018
Messages
720
Reaction score
287
Points
63
Location
Dunbarton NH
Vehicle Year
1989
Make / Model
Ford Bronco II
Engine Type
2.9 V6
Transmission
Manual
2WD / 4WD
4WD
Total Lift
3"
Tire Size
33
I like the bell flare connectors Walker makes better- no gaskets and you can swivel it around to suit you. I weld the male end of the connector to the pipe in front and the female end to the rear section but you could switch it if you want. I couldn't find a picture of the male end but the lower right piece is the female end. No more leaky gaskets.
View attachment 39069
I think this might be the solution. I could weld the one on the bottom right to the muffler and use a donut gasket and spring bolts.
 

Dirtman

Former Middleweight Moss Fighting Champion
Joined
May 28, 2018
Messages
19,304
Reaction score
13,326
Points
113
Location
41N 75W
Vehicle Year
2009
Engine Type
2.3 (4 Cylinder)
Transmission
Automatic
2WD / 4WD
2WD
Total Lift
It's up there.
Total Drop
It's down there.
Tire Size
Round.
My credo
I poop in the furnace.
You dont use a donut with that setup if you use both the male and female end. Its self sealing like a compression fitting.

hed-21153_lv.jpg
 

Sponsored Ad


Sponsored Ad

Staff online

Today's birthdays

Member & Vendor Upgrades

For a small yearly donation, you can support this forum and receive a 'Supporting Member' banner, or become a 'Supporting Vendor' and promote your products here. Click the banner to find out how.

Truck of The Month


Kirby N.
March Truck of The Month

Recently Featured

Want to see your truck here? Share your photos and details in the forum.

Follow TRS On Instagram

TRS Events

25th Anniversary Sponsors

Check Out The TRS Store


Sponsored Ad


Sponsored Ad

Sponsored Ad


Amazon Deals

Top